Replaces

2000-05 Ford Taurus Mercury Sable Shock & Strut Kit - 1ASSP01561

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 
Direct Fit

Fits and functions correctly.  Competitors combine applications to reduce the amount of parts they carry, resulting in: incorrect vehicle height, poor response and an uncomfortable ride.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

Pre-Assembled

Loaded strut & spring assemblies allow for a quicker, safer install than bare struts.  No spring compressor required! 

Trouble-Free Install

Includes the matched parts needed. New components over reused parts provide a better ride and save you from having to repair again.

Matched Parts

Not all shocks and struts are manufactured the same.  Mixing and matching can result in ride quality issues and decrease the life of the parts.

Saves Time & Money

Over buying the parts individually, or having to search different parts that are correct for your vehicle (because we did it for you!)

Part Details

  • Quantity: 4 Piece Set

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Remove the wheel (1:10)
    • Loosen the lug nuts with your lug wrench
    • Raise and secure the vehicle
    • Remove the lug nuts and wheel
  2. step : Remove the front strut (1:31)
    • Use penetrating oil on the strut and shock bolts.
    • Unbolt and unclip the ABS sensor line.
    • Remove the upper stabilizer bolt with an 18 mm wrench.
    • Unbolt the lower end of the strut and use a hammer to work the bolt out.
    • Use a hammer to separate the steering knuckle and the strut.
    • Remove the three 13 mm bolts at the top of the strut.
  3. step : Install the new strut (4:05)
    • Finesse the strut into place and bolt in the three 13 mm bolts
    • Torque the three 13 mm bolts to 35 ft lbs.
    • Taking care not to damage the brake lines, work the bottom of the strut into the steering knuckle.
    • Bolt in the bottom of the strut, torquing the bottom bolt to 100 ft lbs.
    • Bolt the stabilizer link back in, using your 18 mm wrench to tighten it up.
    • Clip the ABS sensor and brake line bracket back together and bolt it back in place.
  4. step : Put the wheel back on (8:38)
    • Put the wheel on and hand tighten the lug nuts.
    • Lower the car
    • Torque the lug nuts using a star pattern from 75-100 ft lbs

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Large Hammer
  • Jack Stands

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Sockets - Metric

  • 13mm Socket
  • 16mm Socket
  • 14mm Socket
  • 18mm Socket
  • 17mm Socket
  • 12mm Socket
  • 11mm Socket
  • 15mm Socket
  • 10mm Socket

  • Wrenches - Metric

  • 15mm Wrench
  • 10mm Wrench
  • 21mm wrench
  • 13mm Wrench
  • 12mm Wrench
  • 16mm Wrench
  • 11mm Wrench
  • 17mm Wrench
  • 19mm Wrench
  • 18mm Wrench
  • 14mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 2000-2005 Ford Taurus Wagon Front & Rear Shock & Strut Kit 4 Piece Set
  • 2000-2005 Mercury Sable Wagon Front & Rear Shock & Strut Kit 4 Piece Set

This part replaces:

  • Monroe 171615
  • Monroe 181615
  • Monroe 5971
  • KYB 344434
  • KYB SR4009
  • KYB SR4010
Part #: 1ASSP01561

Out of Stock

How-to Video:

(09:39 min)