Replaces

2000-05 Ford Focus Strut & Spring Assembly - 1ASFK04174

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Includes:   with Sway Bar Links
  • Quantity:   4 Piece Set

Specifications:

  • Brand New Suspension Kit
  • Comes as a 4 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 
Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Accessing the Shocks and Struts (1:03)
    • Loosen the lug nuts on the wheel while the car is on the ground
    • Jack the car up and remove the lug nuts and wheel
    • Pull the brake line from the bracket
    • Pull the ABS sensor out of its bracket
    • Remove the bolt on the upper stabilizer link. Spray with penetrating oil
    • Spray the bolt on the back side of the strut with penetrating oil
    • Use a socket to remove the 15mm bolt on the steering knuckle
  2. step : Removing the Strut (4:27)
    • Spray penetrating oil where the strut connect with the steering knuckle
    • Use a 15mm socket to disconnect the tie rod. Use a jack and some wood to hold the tie rod up to help remove the bolt
    • If the vehicle has a broken spring lift up on the strut and hammer the steering knuckle until it loosens
    • Lift the strut up and out of the steering knuckle
    • Remove the three 13mm bolts up in the engine compartment
    • Pull the strut free
  3. step : Installing a New Strut (6:40)
    • With the clip on the bottom of the strut facing inward, put the strut into place
    • Replace the bolts in the engine compartment
    • Pull the steering knuckle out and slide it on to the bottom of the strut
    • Replace the bolt that connects the strut to the steering knuckle. Do not tighten fully
    • Make sure the steering knuckle is below the taper on the strut
    • Make sure its at the right depth and moves properly
    • Tighten the bolt on the steering knuckle to between 65 and 70ft/lbs
  4. step : Reconnecting the Brackets and Sensors (9:52)
    • Put the brake line back in place
    • Put the tie rod back in place and replace the nut
    • Replace the stabilizer link and bracket. Tighten the nut
    • Put the ABS sensor back in place
    • Jack the tie rod up and tighten the nut to 55 to 60ft/lbs
    • Replace the wheel and thread the lug nuts
    • Lower the car and tighten the lug nuts to 100ft/lbs in a crossing pattern
    • Tighten the bolts in the engine compartment to between 25 and 30ft/lbs

Tools needed for replacement:

    General Tools

  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Sockets - Metric

  • 13mm Socket
  • 15mm Socket
  • 17mm Socket
  • 19mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver

  • Wrenches - Metric

  • 17mm Wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2000-2005Ford Focus Ford Focus (excluding SVT Models) Front Strut & Spring Assembly with Sway Bar Links 4 Piece Set
Part #: 1ASFK04174


Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(13:03 min)