Replaces

2000-05 Ford Excursion Fuel Pump Module Assembly TRQ FPA61980

00-05 Ford Excursion w/5.4L, 6.8L (exc CA Emissions) Fuel Pump Module w/ Sending Unit

See more Fuel Pumps & Assemblies >>>

$ 89.95

$123.95

27% OFF

$123.95

27% OFF

FREE SAME DAY SHIPPING

Read 2 REVIEWS

FPA61980

In Stock

This part doesn’t fit a . Select from parts that fit.

Show parts that fit

Orders must be placed by 2pm ET

1A Auto Lifetime Warranty

See more Fuel Pumps & Assemblies >>>

Frequently bought together

2000-05 Ford Excursion Fuel Pump Module Assembly TRQ FPA61980

$89.95

Quick Disconnect Pliers

$35.45

Description

Vehicle Fit

Warranty & Shipping

Part Details

Resistance Ohms Full: 160 Ohms
Fuel Tank Pressure Sensor Included: No
Gasket Or Seal Included: Yes
In Tank or External: In Tank
Outlet Quantity: 1
Lock Ring Included: Yes
Inlet Type: Strainer
Fuel Type: Gas
Pump Type: Electric
Strainer Included: Yes
Maximum Flow Rating: 34.34 gph
Minimum Flow Rating: 26 gph
Average Flow Rating: 30 gph
Resistance Ohms Empty: 15 Ohms
Minimum Pressure: 79.7 PSI
Inlet Quantity: 1
Outlet Type: Quick Connect
Fuel Sending Unit Included: Yes
Outlet Outside Diameter: 9.49 mm
Maximum Pressure: 108.7 PSI
Wire Harness Included: No

Product Features

Complete Assembly: No modifications or assembly required

Carbon Brush and Commutator: More than twice the service life compared to copper

Flourine Rubber Seals: Resistant to high temperature, fuel, and solvents

SAE J2044 Compliant: Improved mounting security, minimized installation error

Item Condition: New

Attention California Customers:

proposition 65 icon WARNING: This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

Product Reviews

Loading reviews

5.00/ 5.0

2000 Ford Excursion Fuel Pump.

The pump came and i proceeded to change it. Very simple 4 18 mil bolts loosen a couple of hoses and its good to go. I used three floor jack because it was full of gas. Hardest thing is the removal of the retaining ring that keeps the pumps metal ring stationary on the tank. The new pump came nicely packaged, i compared both, they seem to be exact. Installation is straight forward. After the fuel line and return is disconnected, inside the tank are to clips that need to be released for the removal. Make sure the new sock on the assembly slides through the opening and you hear the click. Fuel level float points towards the front of the vehicle. Anti seize the bolts , put a coating of grease on the vent and fill tubeas well as the fuel return hose. I connected the two fuel lines,, fuel return i plugged the power source in, and connected the vent hose. I jacked the tank up as straight as i could. Lined up front holes, installed the bolts about 8 turns jacked the rear of the tank

Fuel pump saved the day.

Simmie

Great product, it fixed me right up!

Customer Q&A

Does the pump fit a plastic tank?

September 14, 2018

C H

This part is specific to vehicles with a particular set of options. We will need more information about your vehicle to confirm the fit.

September 14, 2018

Jessica D

Does this pump work on the 6.8 V10 ?

January 4, 2022

Mike J

This part will fit the 2000-2005 Ford Excursion V10 6.8L without California Emissions.

January 4, 2022

Andra M

Yes, Installed into a 2002 Excursion. Works fine. Only issue I had was the fuel level is a bit off and that is probably my fault. I must have bent it going in, or old one coming out. I used the old one to set my new float. I didn't want to pay to pull the tank, since it had just been topped. I cut a hole above the tank based on measurements I found online and was able to do it from above. That made removing the ring around a bit harder and also placing it back, making sure it was sealed. I also had to cut the old wires to attach them to the new pump.

January 5, 2022

MARIO G