Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

This hazard warning switch is a new, aftermarket replacement part. It is designed to REPLACE original hazard switches that may have corroded or been damaged causing an electrical failure in your emergency warning system. If your hazard lights are not working because of a defective emergency switch, then this is just what you need to get your vehicle in good working order again!

This hazard switch has the following specifications:

  • Dash mounted
  • Correct plug configuration
  • Replaces dealer part number: 10359032
  • Direct plug in installation
  • Built to strict quality control standards
  • 100% electrically tested

 

Our electrical and electronic parts are subject to strict quality control testing. Please ensure proper diagnosis of this item before purchasing as the item cannot be returned once installed or plugged in.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Lower Dash Panel (0:35)
    • Press the tabs on the lower panel beneath the steering wheel and pull it down
    • Twist the socket free from the panel
    • Remove the bulb from the socket
    • Remove the two 7mm bolts from the dash trim panel
    • Unclip and pull the dash trim panel
    • Remove the trunk switch harness with a flat blade screwdriver
  2. step : Removing the Steering Wheel Panel (1:30)
    • Lift up the steering wheel
    • Remove the T25 screw underneath the steering wheel
    • Pry out on the steering wheel lever
    • Pull the lower steering wheel panel down and out
    • Remove the E5 External Torx bolts from below the steering wheel
    • Pull the upper steering wheel panel up and off
  3. step : Removing the Dash Trim Panel (2:31)
    • Unclip and pull out the fuse panel door
    • Remove the 7mm bolt from the dash trim panel with a socket and ratchet
    • Open the glove compartment and remove the 7mm bolt from the dash trim panel
    • Pry off the ignition bezel with a flat blade screwdriver
    • Pull out and unclip either side of the dash panel
    • Pull the dash panel forward
    • Use a flat blade screwdriver to disconnect the hazard switch without breaking the bezel
    • Turn the car on
    • Pull the shifter back all the way
    • Pull the dash panel up and out
  4. step : Removing the Hazard Switch (3:58)
    • Remove the hazard switch bezel with a flat blade screwdriver without breaking it
    • Support the switch from the bottom and pry on the tab to release it
  5. step : Installing the New Hazard Switch (4:16)
    • Open the glove compartment
    • Turn the car on
    • Pull the shifter back all the way
    • Pull the steering wheel down
    • Reinstall the headlight switch harness
    • Replace and tighten the three 7mm bolts on the headlight switch
  6. step : Reinstalling the Dash Trim Panel (4:26)
    • Open the glove compartment
    • Turn the car on
    • Pull the shifter back all the way
    • Pull the steering wheel down
    • Line up the dash trim panel
    • Reconnect the hazard switch
    • Slide the shifter forward and remove the key
    • Re-clip the dash panel
    • Replace and tighten the 7mm bolts into the dash trim panel
    • Replace the ignition bezel
  7. step : Reinstalling the Steering Wheel Panel (5:50)
    • Tilt the steering wheel down
    • Reconnect the upper steering wheel panel
    • Replace and tighten the E5 External Torx bolts
    • Re-clip the hooks on the lower panel push it up until it clicks
    • Replace and tighten the T25 Torx screw
  8. step : Reinstalling the Lower Dash Panel (6:48)
    • Reconnect the trunk switch harness
    • Push the dash trim panel into place
    • Replace and tighten the 7mm bolts
    • Twist the bulb into the socket on the panel
    • Push the lower panel into place beneath the steering wheel until it clicks

Tools needed for replacement:

    Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 7mm Socket

  • Torx Drivers & Sockets

  • T25 Torx Driver
  • E5 Inverted Torx Socket

1.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
0
0
0
0
1
Made in China switches - no good
I would have give zero stars if that was a choice. The first switch didnt work. They sent a second switch; same problem. No refund on electrical parts. I used a switch from a junkyard car and it worked. Spend a little more and get a better switch. 1AAuto has great videos, but I would think twice before ever ordering parts from them again.
April 27, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Does this switch come with the actual button that you push (The black plastic piece with the hazard logo on it?) Or just the green relay box?
Adam F June 22, 2018
No button..just relay ( sold separately) on dash above vents
A N June 22, 2018
Just the green relay box
T H June 22, 2018
Just the green relay box. Black button with logo is separate piece.
Joseph B June 22, 2018
It does not come with the button. Just the green switch.
Jordan A June 22, 2018
Just the green relay switch.
C A June 22, 2018
can i purchase just the button cover? My switch is fine...just missing the printed cover. you specified in another response that itbwas a separate part....but i cant find where to get one. thanks!!
Z. E September 3, 2018
Hello, We are unable to sell just the button cover as all our items come prepackaged from the manufacturer. Thank you!
Zach B September 3, 2018
We do not currently a full assembly with the button. We’re always updating our inventory so check back soon! If you have any other questions, please let us know.
Jessica D September 4, 2018
Year Make Model Description
2000-2005Chevy Monte Carlo Chevy Monte Carlo SS Hazard Switch
2000-2005Chevy Monte Carlo Chevy Monte Carlo Hazard Switch
Part #: 1AZMX00017


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(08:15 min)