Replaces

2000-04 Jeep Grand Cherokee Door Lock Actuator & Integrated Latch - 1ADLA00093

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

This is a power door lock actuator & latch assembly that mounts inside the door. It is designed to replace a malfunctioning original unit.

Specifications:

  • Fits RH (Passenger Side) FRONT
  • Integrated latch & lock actuator assembly
  • Replaces dealer part numbers: 55135-606AB, 55363-472AA, 55363-472AB, 55363-472AC, 55363-472AD, 55363-472AE, 55363-472AF, 55135606AB, 55363472AA, 55363472AB, 55363472AC, 55363472AD, 55363472AE, 55363472AF
  • Electrically operated
  • Direct replacement
  • Built to strict quality control standards
This power door lock actuator assembly is a great replacement and has good cost savings over an actuator from the dealer.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Door Panel (1:09)
    • Pry off the trim piece inside the door pull with a flat blade screwdriver
    • Pry off the door handle bezel with a flat blade screwdriver
    • Pry off the window switch with a flat blade screwdriver
    • Disconnect the window switch wiring harness
    • Remove the two 7mm bolts inside the door pull
    • Pry off the door panel by hand
  2. step : Accessing the Door Lock Mechanism (2:58)
    • Remove the 10mm bolt from the door handle
    • Pull the door handle forward and out
    • Pull of the latch and lock rod clips
    • Pull the latch rod and lock rod out of the door handle
    • Peel back the water shield
  3. step : Removing the Door Lock Mechanism (3:58)
    • Pull the lock knob rod out of the yellow clip
    • Remove the three T30 Torx bolts from the lock mechanism
    • Pull the lock mechanism down, while keeping the latch rods from falling into the door
    • Separate the latch and lock rods from the lock mechanism
    • Disconnect the wiring harnesses from the lock mechanism
    • Pull the lock mechanism out of the door
  4. step : Separating the Door Lock Actuator (5:43)
    • Carefully remove the three T10 Torx bolts that hold the actuator to the lock mechanism
    • Pull the actuator away from the lock mechanism
  5. step : Connecting the New Door Lock Actuator (6:18)
    • Push the door lock actuator shoe into the lock mechanism
    • Twist the actuator into place
    • Line up the actuator and lock mechanism gear teeth
    • Insert the three T10 Torx bolts into the actuator
  6. step : Reinstalling the Door Lock Mechanism (7:11)
    • Attach the rod with the white wrap to the upper lock clip
    • Attach the rod with the yellow wrap to the lower lock clip
    • Attach the wiring harnesses to the lock mechanism
    • Push the mechanism into place
    • Start the three T30 Torx screws by hand
    • Reconnec the lock knob rod to the yellow clip
    • Test that the door lock works
  7. step : Reinstalling the Door Handle (9:06)
    • Put the water shield on
    • Attach the latch rods to the door handle using the clips
    • Push the door handle into place
    • Insert the 10mm bolt into the door handle
  8. step : Reinstalling the Door Panel (10:41)
    • Pull the wiring harnesses through their cavity
    • Lift the door panel into place
    • Push the door panel clips in
    • Connect the window switch wiring harness
    • Push the door handle bezel into place using the locating tab
    • Insert the two 7mm bolts into the door pull
    • Push the trim piece into the door pull
    • Make sure the door is unlocked

Tools needed for replacement:

    Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 7mm Socket
  • 10mm Socket

  • Torx Drivers & Sockets

  • T30 Torx Driver
  • T10 Torx Driver

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
2000-2004Jeep Grand Cherokee Jeep Grand Cherokee Front Door Lock Actuator & Integrated Latch Passenger Side
Only 1 left in stock
Part #: 1ADLA00093


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(12:24 min)