Replaces

2000-03 Chevy Impala Monte Carlo Radiator Dual Cooling Fan Assembly - 1ARFA00089

Our aftermarket cooling fan assemblies are some of the highest quality replacements on the market! This radiator fan assembly is a complete, ready to bolt on, direct replacement part.

Specifications:

  • New, not rebuilt, electric motor
  • Replaces dealer part number: 89022512
  • Geometrically designed plastic blades for optimal circulation and uniform balance
  • Plastic shroud designed to ensure structural integrity and endurance for maximum performance
  • Performance tested
  • Replaces original assemblies that are melted or worn out
  • Comes with proper plug for trouble free installation

Now you can buy a high quality cooling fan assembly that is built to strict quality control standards. It is a great replacement and has substantial cost savings over a dealer unit.

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Engine Mounts (0:43)
    • Remove the eight 13mm bolts from the engine mounts
    • Loosen the 13mm bolt from the support bar
    • Push the support bar to the side
    • Lift up the two engine mounts
  2. step : Removing the Air Intake Box (1:15)
    • Disconnect the mass airflow sensor harness
    • Loosen the air intake hose clamps with a flat blade screwdriver
    • Pull the intake hose free
    • Loosen the two 8mm bolts from the air box
    • Pull the air intake box forward, up, and out
    • Pull the back of the air intake box out
  3. step : Removing the Radiator Fan (2:05)
    • Remove the 10mm bolt on either side of the radiator fan
    • Remove the 10mm bolt and mount on either upper corner of the radiator fan
    • Disconnect the two fan wiring harnesses
    • Unclip the series of clips along the fan harness with a flat blade screwdriver
    • Clip the wire tie and pull the vacuum hose free
    • Clip the hose clamp with pliers and pull the radiator hose free
    • Tuck the radiator hose behind the engine mount
    • Lift the radiator cooling fan up and out
  4. step : Installing the New Radiator Fan (4:25)
    • Line up the two tabs on the radiator fan with the two slots
    • Place the radiator fan into its slots
    • Replace and tighten the 10mm bolts and the radiator mounts
    • Replace and tighten the lower 10mm bolts on the radiator fan
    • Push the tab on the back of the clips from the old radiator fan and remove them
    • Clip the clips into the new radiator fan
    • Re-clip the harness into the new clips
    • Place the outer air box pins into the rubber grommets
    • Re-clip the larger wire clip and harness back into place
    • Connect the two fan wiring harnesses
    • Push the teeth together on the radiator hose clamp
    • Push the radiator hose into place
  5. step : Installing the Air Intake Hose (7:40)
    • Remove the mass airflow sensor
    • Remove the small ring off the sensor and place it on the intake box
    • Push the tab on the ring between the two posts on the box
    • Push the mass inflow sensor onto the intake hose
    • Lower the intake box and attach it to the sensor
    • Tighten the two hose clamps
    • Reconnect the mass air flow sensor harness
    • Line up the air intake box
    • Tighten the two 8mm bolts on the air intake box
  6. step : Installing the Engine Mount (9:11)
    • Pull the engine mounts down
    • Pull the engine forward and align the engine mounts
    • Replace and tighten the eight 13mm bolts on the engine mounts
    • Tighten the 13mm bolt on the support bar
    • Reconnect the vacuum hose and tighten it with a wire tie

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Wire Ties

  • Pliers, Cutters & misc Wrenches

  • Wire Cutters
  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 8mm Socket
  • 10mm Socket

5.0 / 5.0
10 Reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
10
0
0
0
0
Quality parts.
The dual cooling fan assembly I purchased works perfect. It was easy to install and came with everything I needed. Thanks 1A Auto, you always have the quality parts at a great rate.
June 4, 2018
Purchased
1 month ago
Squeel gone
Fit like the old one. The only problem that I had was I watched your how to replace video and it did not show removing the plastic pin on the bottom, other then that went real well
January 1, 2018
Purchased
6 months ago
Didn't know it could be so easy to change fan motors
My fan motors started squealing on my 2002 Chevy Monte Carlo, so I checked on line how to change them, 1A Auto has the Best Videos, very detailed, & at the end you can order the part you need at a Very Completive Price. We they came the fit like a glove, just like factory fit.
Clint Wildman, Billings, Montana
December 20, 2017
Purchased
6 months ago
AAA+++
Great product and service----Great How To Videos. Will use again.
November 28, 2017
Purchased
7 months ago
Great fan!
Arrived in good condition and on time! Fan works great!
October 11, 2017
Purchased
8 months ago
Perfect fit, best price of them ALL !
Perfect fit, best price of them ALL ! I've been using 1A Auto a lot lately, and finding their quality is GREAT and their prices are better than the 3 local (nat'l chain) parts stores. I will continue to use them, and recommend them.
Mike S.
Grand Junction, Co.
September 24, 2017
Purchased
9 months ago
Great
The part arrived in good condition and on time which was expected I will do all of my business through 1ààuto!
September 13, 2017
Purchased
10 months ago
Fast and easy ordering. I recommend 1 A Auto. Fast and free shipping.
September 5, 2017
Purchased
10 months ago
Parts and Service
In doubt? Don't be... I've been an A1 customer for many years. Headlights, window motors, switches, electric radiator fans, fuel pump, etc. Quality parts at a DIY price.

Recent purchase of fan system arrived damaged. Old fan removed awaiting replacement. Single call to A1 resulted in instant next day delivery. A1 didn't require damaged fan be returned. I donated it to a local garage that repairs cars and gives those cars to needy families in my community

My first choice vendor for auto parts is A1.

Joe in Tennessee
August 14, 2017
Purchased
10 months ago
Great dual cooling fan.
Great Product at a great price. It matched the original and bolted right up. Plugged right in. I priced this at several retail auto parts stores and this was cheaper by far with no modifications required.And shipping is free.
March 18, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 2 answers
I have a question bout my car keeps over heating and idk if it is my radiator got a leak or transmission. Can somebody help me..?
Tyrell H on Mar 20, 2018
BEST ANSWER: 3.8 engines tend to leak at the water pump or at the 2 elbows just above there. Any repair should also include replacing the thermostat while you making repairs. Coolant system needs to be bled to remove any air. You will be wise to check a few toutube videos and invest in a repair manual.

Vehicle Fit

  • 2000-2003 Chevy Impala Radiator Dual Cooling Fan Assembly with Standard Cooling
  • 2000-2003 Chevy Monte Carlo Radiator Dual Cooling Fan Assembly

This part replaces:

  • Partslink GM3115122 / GM3117104
  • Hollander 674-00818A
  • OE # 89022512
  • Dorman 620-616
  • TYC 620380
  • DEPO 335-55001-000
Part #: 1ARFA00089

How-to Video:

(10:17 min)