Replaces

1999-04 Jeep Grand Cherokee Steering & Suspension Kit - 1ASFK04214

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Bearing Type:   Ball Bearing
  • Quantity:   4 Piece Set
  • Kit Includes:
      (1) Steering Arm to Center Link Tie Rod
      (2) Front Hub Assemblies
      (1) Front Driver Side Outer Tie Rod

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a Set of 4
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Remove the wheel (1:18)
    • Loosen the lug nuts and the hub nut.
    • Raise and secure the vehicle
    • Remove the lug nuts and the wheel.
    • Remove the hub nut with a 1-7/16 socket after removing the cotter pin and washer.
    • Have a helper hold down the brakes to allow you to break the nut loose.
  2. step : Disassemble the brakes (2:12)
    • Compress your caliper using a flat blade screwdriver.
    • Unbolt the caliper with 11/16 inch socket and ratchet.
    • Remove and inspect the brake pads.
    • If they are worn out, replace them during reassembly.
    • Use wire ties to secure the caliper up and out of the way.
    • Remove the caliper bracket by unbolting the 3/4 inch bolts.
    • Pull the brake disc/rotor off and inspect for wear.
    • If it shows signs of needing to be changed, such as deep grooves, replace during reassembly.
  3. step : Remove the hub (7:45)
    • Use a hammer to break the axle loose.
    • Hit the three 13 mm 12 point nuts with some penetrating oil and use a breaker bar, socket and ratchet to remove.
    • Remove the hub bolts and use a hammer to work the hub out and off.

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Jack Stands
  • Floor Jack

  • Ratchets & Related

  • Socket Driver
  • Ratchet
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 13mm Socket

  • Sockets - SAE

  • 3/4 Inch Socket
  • 11/16 Inch Socket
  • 1-7/16 Inch Socket

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1999-2004Jeep Grand Cherokee Jeep Grand Cherokee 4 Wheel Drive Steering & Suspension Kit 4 Piece Set
Part #: 1ASFK04214


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(10:54 min)