Replaces

1999-04 Jeep Grand Cherokee Brake Rotor Pair Nakamoto 5118-DSZ - 1APBR00085

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Front Brake Rotor Specifications:
      12.01" (305mm)
      Vented
      5 Lug
  • Quantity:   Pair
  • Brake Rotor Type:   Cross Drilled & Slotted
  • Brake Rotor Coating:   Zinc Coated
  • Product Line:   Performance

These front performance brake rotors are just what you need to get your vehicle stopping great again!

Specifications:

  • Comes as a matched pair
    • Includes both LH (Driver) & RH (Passenger) Side Front
  • Cross drilled, Slotted, And Zinc Coated
  • Fits 5 Stud Wheels
  • Vented
These brake rotors make a great replacement and are an excellent performance upgrade over your worn original rotors.
Zinc Coated

Helps reduce rust and corrosion for a longer-lasting and better looking rotor.

"True" Non-Interference Vane Design

Retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots remove brake dust and expel gasses during hard braking.

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (1:19)
    • Loosen the lug nut covers with a 19mm socket
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:43)
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Remove 1bolts from the brake caliper with an 11/16 socket
    • Pull the caliper aside
    • Pry out the pins from the brake pads
    • Pry the brake pads off with a flat blade screwdriver
    • Unclip the ABS sensor wiring harness
    • Remove 3/4 inch bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Remove the Phillips screws from the rotor
    • Pull the rotor off
    • If the rotor will not pull off, thread some bolts into the slot on the rotor, and tighten them to loosen the rotor
  3. step : Installing the New Brake Rotor and Brake Pads (5:48)
    • Clean off the hub with a wire brush
    • Slide the rotor on
    • Clean both sides of the rotor with brakes parts cleaner
    • Thread on one lug nut to hold the rotor in place
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Apply grease to the caliper slide bolts
    • Clean the caliper bracket and brake pad slides with a wire brush
    • Put the bracket back into place
    • Start the bolts by hand
    • Tighten the bolts to 85 foot-pounds of torque
    • Apply grease to the brake pad tabs
    • Install the new brake pads into the bracket
    • Put the caliper on
    • Thread bolts by hand
    • Secure the caliper slide pin with locking pliers
    • Tighten bolts to 20 foot-pounds
    • Remove the lug nut
  4. step : Reattaching the Wheel (10:53)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the 19mm lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
  5. step : Testing the Brakes (11:18)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Hammer
  • Jack Stands
  • Wire Brush
  • Floor Jack

  • Ratchets & Related

  • Socket Extensions
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - SAE

  • 3/4 Inch Socket
  • 11/16 Inch Socket

5.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
The parts and service are outstanding I recommend 1A Auto to everyone I know and I am a delivery person I find that the parts from 1A Auto last longer than my local auto parts store more durable and and for the money 1A Auto offers a better product for example I can get cross drilled and slotted rotors 4 less than the price of a regular rotor and as I said before I am in the delivery business and I use my personal vehicle so when it comes to brakes ball joints wheel bearings and tie rods A-1 Auto my place to go
September 30, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1999-2004Jeep Grand Cherokee Jeep Grand Cherokee Front Cross Drilled & Slotted Zinc Coated Brake Rotor Pair Performance Nakamoto
Part #: 1APBR00085


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Nakamoto
Brand #: 5118-DSZ

How-to Video:

(11:50 min)