Replaces

1999-04 Honda Odyssey Wheel Bearing & Hub Assembly TRQ BHA85003 - 1ASHS01220

 

Precision Engineered:

From the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.
100% Factory tested to precise OEM tolerances.

Highest Quality Materials:

High quality, multi-lip seal reduces the intrusion of dirt and water. Heavy duty grease resists high temperature, moisture, and reduces intense friction.

Direct Fit Replacement:

Guaranteed to fit and function correctly for your specific application.

Part Details

  • Includes: (1) 36mm Axle Nut Socket

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:59)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:24)
    • Remove the two 12mm bolts from the brake caliper
    • Pull the caliper toward the outside of the vehicle to push in the pistons
    • Pull the caliper aside
    • Pull the brake pads off by hand
  3. step : Removing the Brake Rotor (2:16)
    • Remove the two 14mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Remove the two screws from the rotor with an impact screwdriver and a hammer
    • Pull the rotor off
    • If the rotor will not come off, strike it with a hammer
  4. step : Removing the Wheel Hub (3:35)
    • Remove the dust cover with a hammer and chisel
    • Straighten the hub nut with a hammer and chisel
    • Remove the 36mm hub nut
    • Pull the hub off
  5. step : Installing the New Hub (4:44)
    • Push the new hub on
    • Start the 36mm hub nut
    • Tighten the hub nut to 181 foot-pounds of torque
    • Serrate the nut with a hammer and punch
  6. step : Installing the New Brake Rotor (5:23)
    • Slide the rotor on
    • Insert the two screws into the brake rotor
    • Remove the rubber plug from the old brake rotor
    • Push the rubber plug into the new brake rotor
    • Clean the brake pad slides with a wire brush
    • Check that the caliper slides move freely
    • If the caliper slides do not move freely, apply grease to the slides
    • Put the bracket back into place
    • Start the 14mm bolts by hand
    • Tighten the 14mm bolts to 45 foot-pounds of torque
  7. step : Installing the New Brake Pads (7:06)
    • Install the new brake pads into the bracket
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Put the caliper on
    • Thread the 12mm bolts by hand
    • Tighten the 12mm bolts to 20 foot-pounds
    • Put on the hub dust cover
    • Tap on the dust cover with a hammer
  8. step : Reattaching the Wheel (8:57)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 90 - 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  9. step : Testing the Brakes (9:34)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Hammer
  • Chisel
  • Jack Stands
  • Large C-Clamp
  • Center Punch
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Bearing Grease

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver
  • Impact Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 36mm Socket
  • 12mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 14mm Wrench
  • 12mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1999-2004 Honda Odyssey Rear Wheel Bearing & Hub Assembly Pair with (1) 36mm Axle Nut Socket TRQ

This part replaces:

  • TRQ BHA85003
Part #: 1ASHS01220


Order must be placed by 4pm ET
TRQ
Brand #: BHA85003

How-to Video:

(10:05 min)