1999-04 Honda Odyssey Wheel Bearing & Hub Assembly TRQ BHA54246 - 1ASHR00117

This replacement hub & bearing assembly is just what you need to get your vehicle in good working order again.


  • Fits either LH (Driver Side) or RH (Passenger Side) REAR
  • Replaces dealer part numbers: 42200-S0X-A50, 42200-S0X-A51, 42200-S0X-A52, 42200S0XA50, 42200S0XA51, 42200S0XA52
  • Fits 5 Lug Wheel
  • New studs already installed
  • Direct replacement
  • Built to strict quality control standards


  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hub & bearings are all tested prior to shipping.

Fit Guaranteed

  • This hub & bearing will install just as your original does. You can use your existing hardware.
  • Save time and money with this direct fit hub bearing assembly. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.


  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.
Precision Engineered

Precision Engineered using the highest grade SAE 1055 / 65Mn high carbon steel to exact OEM design.

100% Factory tested to precise OEM tolerances.

Highest Quality Materials

High quality, multi-lip seal reduces the intrusion of dirt and water, keeping grease clean for a longer bearing life.

Premium, heavy duty grease resists high temperature, moisture, and reduces intense friction pressure to help extend the life of the bearing.

Direct Fit Replacement

Direct fit replacement part is guaranteed to fit and function correctly for your specific application

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

BHA54246 Axle / Spindle Nut Torque Specification
  1. step : Removing the Wheel (0:59)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:24)
    • Remove the two 12mm bolts from the brake caliper
    • Pull the caliper toward the outside of the vehicle to push in the pistons
    • Pull the caliper aside
    • Pull the brake pads off by hand
  3. step : Removing the Brake Rotor (2:16)
    • Remove the two 14mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Remove the two screws from the rotor with an impact screwdriver and a hammer
    • Pull the rotor off
    • If the rotor will not come off, strike it with a hammer
  4. step : Removing the Wheel Hub (3:35)
    • Remove the dust cover with a hammer and chisel
    • Straighten the hub nut with a hammer and chisel
    • Remove the 36mm hub nut
    • Pull the hub off
  5. step : Installing the New Hub (4:44)
    • Push the new hub on
    • Start the 36mm hub nut
    • Tighten the hub nut to 181 foot-pounds of torque
    • Serrate the nut with a hammer and punch
  6. step : Installing the New Brake Rotor (5:23)
    • Slide the rotor on
    • Insert the two screws into the brake rotor
    • Remove the rubber plug from the old brake rotor
    • Push the rubber plug into the new brake rotor
    • Clean the brake pad slides with a wire brush
    • Check that the caliper slides move freely
    • If the caliper slides do not move freely, apply grease to the slides
    • Put the bracket back into place
    • Start the 14mm bolts by hand
    • Tighten the 14mm bolts to 45 foot-pounds of torque
  7. step : Installing the New Brake Pads (7:06)
    • Install the new brake pads into the bracket
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Put the caliper on
    • Thread the 12mm bolts by hand
    • Tighten the 12mm bolts to 20 foot-pounds
    • Put on the hub dust cover
    • Tap on the dust cover with a hammer
  8. step : Reattaching the Wheel (8:57)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 90 - 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  9. step : Testing the Brakes (9:34)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Hammer
  • Chisel
  • Jack Stands
  • Large C-Clamp
  • Center Punch
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Bearing Grease

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver
  • Impact Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 36mm Socket
  • 12mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 14mm Wrench
  • 12mm Wrench

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
Odyssey Hub/Bearing Assembly
Very pleased with this hub/bearing assembly. It was 1/2 the cost at local auto part stores and carries a lifetime warranty. The process was very simple and the online video was reassuring and very accurate. I wouldn’t hesitate to buy again if needed.
November 22, 2017
7 months ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1999-2004 Honda Odyssey Rear Wheel Bearing & Hub Assembly TRQ

This part replaces:

  • OE # 42200S0XA52
  • Hollander 538-58745
  • TRQ BHA54246
Part #: 1ASHR00117

Brand #: BHA54246

How-to Video:

(10:05 min)