Replaces

1999-04 Honda Odyssey Wheel Bearing & Hub Assembly Rear Pair Timken 512180 - TKSHS00093

TIMKEN WHEEL BEARING & HUB ASSEMBLIES: 512180

These replacement wheel bearing & hub assemblies are just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assemblies
  • Comes as a PAIR
    • Fits both the LH (Driver Side) & RH (Passenger Side) REAR
  • Replaces dealer part numbers: 42200-S0X-A50, 42200-S0X-A51, 42200-S0X-A52, 42200S0XA50, 42200S0XA51, 42200S0XA52
  • Fit 5 Lug Wheels
  • New studs already installed
  • Direct replacements
  • Built to strict quality control standards

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hubs & bearings are all tested prior to shipping.

Fit Guaranteed

  • These hub & bearing sets will install just as your originals do. You can use your existing hardware.
  • Save time and money with direct fit hub bearing assemblies. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

Note: These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:59)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:24)
    • Remove the two 12mm bolts from the brake caliper
    • Pull the caliper toward the outside of the vehicle to push in the pistons
    • Pull the caliper aside
    • Pull the brake pads off by hand
  3. step : Removing the Brake Rotor (2:16)
    • Remove the two 14mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Remove the two screws from the rotor with an impact screwdriver and a hammer
    • Pull the rotor off
    • If the rotor will not come off, strike it with a hammer
  4. step : Removing the Wheel Hub (3:35)
    • Remove the dust cover with a hammer and chisel
    • Straighten the hub nut with a hammer and chisel
    • Remove the 36mm hub nut
    • Pull the hub off
  5. step : Installing the New Hub (4:44)
    • Push the new hub on
    • Start the 36mm hub nut
    • Tighten the hub nut to 181 foot-pounds of torque
    • Serrate the nut with a hammer and punch
  6. step : Installing the New Brake Rotor (5:23)
    • Slide the rotor on
    • Insert the two screws into the brake rotor
    • Remove the rubber plug from the old brake rotor
    • Push the rubber plug into the new brake rotor
    • Clean the brake pad slides with a wire brush
    • Check that the caliper slides move freely
    • If the caliper slides do not move freely, apply grease to the slides
    • Put the bracket back into place
    • Start the 14mm bolts by hand
    • Tighten the 14mm bolts to 45 foot-pounds of torque
  7. step : Installing the New Brake Pads (7:06)
    • Install the new brake pads into the bracket
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Put the caliper on
    • Thread the 12mm bolts by hand
    • Tighten the 12mm bolts to 20 foot-pounds
    • Put on the hub dust cover
    • Tap on the dust cover with a hammer
  8. step : Reattaching the Wheel (8:57)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 90 - 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  9. step : Testing the Brakes (9:34)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Hammer
  • Chisel
  • Jack Stands
  • Large C-Clamp
  • Center Punch
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Bearing Grease

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver
  • Impact Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 36mm Socket
  • 12mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 14mm Wrench
  • 12mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1999-2004 Honda Odyssey Rear Wheel Bearing & Hub Assembly Pair Timken 512180

This part replaces:

  • Timken 512180
Only 2 left in stock
Part #: TKSHS00093


Timken
Brand #: 512180

How-to Video:

(10:05 min)