Replaces

1999-04 Honda Odyssey Strut & Spring Assembly Front - 1ASTS00575

In the past, replacing struts required specialized tools to compress, remove and transfer the old spring and mount.  Pre-assembled with all new parts, our complete strut and spring assemblies make this job much quicker and easier for the do-it-yourself mechanic.

Each complete strut & spring assembly contains:

  • Upper Strut Mount
  • Strut Bearing
  • Coil Spring
  • Boot & Bumper Kit
  • Gas-charged Strut 

To ensure the vehicle performs safely and as designed, we recommend replacing shocks & struts in pairs. If the damping rates are significantly different from side to side (like using different brand parts or mixing old with new) the vehicle body and wheel movement variations could cause handling irregularities. We also recommend performing an alignment after replacement. This will ensure proper tracking and protect your vehicle's tires from premature wear.

Pre-Assembled

Pre-assembled, loaded strut & spring assemblies allow for a quicker, safer install than replacing with just bare struts. 

Trouble-Free Install

Trouble-free install includes the matched parts needed to get the job done. New mounts, bearings, springs and hardware will provide a better ride for your vehicle and save you time from not having to do the job again because a used part failed afterwards.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel (1:02)
    • Loosen the lug nuts with a lug wrench
    • Raise and secure the vehicle
    • Remove the lug nuts and wheel.
  2. step : Remove the bottom of the strut (1:35)
    • Apply penetrating oil to the nuts on the bottom of the strut.
    • Use a breaker bar and penetrating oil to unbolt the 18 mm strut bolts on the bottom
    • Unclip the ABS sensor wire.
  3. step : Remove the top of the strut (4:35)
    • Pop the hood and secure it.
    • Use a flat blade screwdriver to pry up the little covers to access the 14 mm nuts.
    • Apply penetrating oil to the 14 mm nuts at the top of the strut.
    • Hold onto the strut as you remove it.
  4. step : Install the new strut (6:03)
    • Bolt the strut back in, torquing your 14 mm bolts to 30 ft lbs
    • Have someone help you guide the top of the strut into place and get the nuts started under the cover.
    • Insert your spindle to the lower end of the strut and raise your control arm until the bolt holes line up.
    • Torque the bottom 18 mm nut to 85 ft lbs
    • Make sure you don’t pinch your ABS wire and its placed correctly.
  5. step : Replace the wheel (9:40)
    • Put the wheel on and hand tighten the lug nuts.
    • Lower the vehicle and torque the lug nuts to 100 ft lbs using a star pattern.

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Floor Jack

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket
  • 18mm Socket
  • 22mm Socket
  • 19mm Socket
  • 20mm Socket

  • Wrenches - Metric

  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1999-2004 Honda Odyssey Strut & Spring Assembly Front Driver Side

This part replaces:

  • Hollander 527-59546L
  • Monroe 171598
  • KYB SR4072
Part #: 1ASTS00575


How-to Video:

(10:26 min)