Replaces

1999-04 Honda Odyssey Steering & Suspension Kit - 1ASFK04631

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a Set of 6
  • Direct replacements
  • Built to strict quality control standards

 

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Separating the Control Arm from the Knuckle (1:02)
    • Loosen the lug nuts.
    • Lift the car, and remove the lug nuts the rest of the way.
    • Using pliers and a pick remove the ball joint pin.
    • Spray penetrating oil on the ball joint nut.
    • Using a wrench remove the ball joint nut.
    • Put the nut back on partially.
    • Use a ball joint fork and separate the ball joint from the lower control arm.
    • Remove the nut.
    • Pry the lower control arm out of the knuckle.
  2. step : Removing the Control Arm (3:36)
    • Spray the bolts on the control arm with penetrating oil.
    • Remove the two bolts from the control arm.
    • Pull the control arm down and out.
  3. step : Replacing the Control Arm (5:06)
    • Replace the rear bolt partially.
    • Rotate the control arm into place and push the ball joint into the knuckle.
    • Pry the control arm up to align the holes and replace the bolt.
    • Replace the ball joint nut.
    • Replace the pin.
    • Jack up the ball joint end of the control arm until all the support is on the suspension.
    • Torque the control arm bolts to 90 – 95ft/lbs.
    • Lower the control arm jack.
    • Put the wheel in place and replace the lug nuts.
    • Lower the vehicle and torque the lug nuts to 95 – 100ft/lbs. in a crossing pattern.

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Pick

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • A Piece of Pipe (for leverage)
  • Ratchet

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 19mm Socket

  • Specialty Tools

  • Pickle Fork

  • Wrenches - Metric

  • 17mm Wrench
  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1999-2004 Honda Odyssey Steering & Suspension Kit 6 Piece Set

This part replaces:

  • Dorman 521-352
  • Dorman 521-351
  • Hollander 512-58464R
  • Hollander 512-58464L
  • OE # 53540S0XA02, 53540S0XA01
  • OE # 51350S0XA02
  • OE # 06513-S0X-A00, 51320S0XA02
  • OE # 51360S0XA02
  • Moog K90349
  • Moog ES3669
  • Moog K620326
  • Moog K620325
Part #: 1ASFK04631


How-to Video:

(08:33 min)