1999-04 Honda Odyssey Rear Wheel Bearing & Hub Assembly Timken 512180 - TKSHR00042

Frequently bought together

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit


This replacement wheel bearing & hub assembly is just what you need to get your vehicle in good working order again.


  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits either LH (Driver Side) or RH (Passenger Side) REAR
  • Replaces dealer part numbers: 42200-S0X-A50, 42200-S0X-A51, 42200-S0X-A52, 42200S0XA50, 42200S0XA51, 42200S0XA52
  • Fits 5 Lug Wheel
  • New studs already installed
  • Direct replacement
  • Built to strict quality control standards

These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm -

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge.

  1. step : Removing the Wheel (0:59)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Pads (1:24)
    • Remove the two 12mm bolts from the brake caliper
    • Pull the caliper toward the outside of the vehicle to push in the pistons
    • Pull the caliper aside
    • Pull the brake pads off by hand
  3. step : Removing the Brake Rotor (2:16)
    • Remove the two 14mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Remove the two screws from the rotor with an impact screwdriver and a hammer
    • Pull the rotor off
    • If the rotor will not come off, strike it with a hammer
  4. step : Removing the Wheel Hub (3:35)
    • Remove the dust cover with a hammer and chisel
    • Straighten the hub nut with a hammer and chisel
    • Remove the 36mm hub nut
    • Pull the hub off
  5. step : Installing the New Hub (4:44)
    • Push the new hub on
    • Start the 36mm hub nut
    • Tighten the hub nut to 181 foot-pounds of torque
    • Serrate the nut with a hammer and punch
  6. step : Installing the New Brake Rotor (5:23)
    • Slide the rotor on
    • Insert the two screws into the brake rotor
    • Remove the rubber plug from the old brake rotor
    • Push the rubber plug into the new brake rotor
    • Clean the brake pad slides with a wire brush
    • Check that the caliper slides move freely
    • If the caliper slides do not move freely, apply grease to the slides
    • Put the bracket back into place
    • Start the 14mm bolts by hand
    • Tighten the 14mm bolts to 45 foot-pounds of torque
  7. step : Installing the New Brake Pads (7:06)
    • Install the new brake pads into the bracket
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Put the caliper on
    • Thread the 12mm bolts by hand
    • Tighten the 12mm bolts to 20 foot-pounds
    • Put on the hub dust cover
    • Tap on the dust cover with a hammer
  8. step : Reattaching the Wheel (8:57)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 90 - 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  9. step : Testing the Brakes (9:34)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Hammer
  • Chisel
  • Jack Stands
  • Large C-Clamp
  • Center Punch
  • Floor Jack

  • Materials, Fluids, and Supplies

  • Bearing Grease

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver
  • Impact Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 36mm Socket
  • 12mm Socket
  • 19mm Socket

  • Wrenches - Metric

  • 14mm Wrench
  • 12mm Wrench

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1999-2004Honda Odyssey Honda Odyssey Rear Wheel Bearing & Hub Assembly
Only 4 left in stock
Part TKSHR00042
In Stock

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Brand #: 512180