This axle shaft is a new, aftermarket part. It is just what you need to get your vehicle in good working order!

Specifications:

  • Fits RH (Passenger Side) FRONT OUTER
  • Replaces dealer part numbers: 44305-S0X-A51, 44305-S0X-A52, 44305S0XA51, 44305S0XA52
  • Brand New, not refurbished or rebuilt
  • Built to strict quality control standards
  • No core charge

Note: This is for one axle shaft assembly.

Axle shafts may need replacing for a variety of different reasons. On vehicles that do heavy work or endure other extreme use you can actually break an axle or strip the splines or teeth. More often the CV joint wears out causing noises and vibration while accelerating or turning.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (1:00)
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
    • Kick the tire to loosen the wheel, if necessary
  2. step : Removing the Axle Shaft (1:36)
    • Straighten the axle nut dimple with a hammer and a punch
    • Have an assistant press the brake pedal
    • Remove the 36mm hub nut
    • Remove the cotter pin from the ball joint nut with a pick and needle nose pliers
    • Remove the 17mm nut from the ball joint
    • Thread the 17mm nut partially on
    • Separate the ball joint from the steering knuckle with a pickle fork and a hammer
    • Remove the 17mm bolt from the ball joint
    • Pry down on the lower control arm with a pry bar
    • Pull the ball joint out of the steering knuckle
    • Push the axle out of the hub with a flat blade screwdriver
    • Push the axle away from the transmission with a pry bar and a hammer
    • Pull the axle out through the wheel well
  3. step : Installing the New Axle Shaft (4:58)
    • Push the new axle shaft into the transmission
    • Push the axle shaft into the hub
    • Push the ball joint into the steering knuckle
    • Put the 17mm nut onto the ball joint
    • Turn the nut so that the cotter pin will fit through the castle nut
    • Push the cotter pin into the ball joint nut
    • Thread on the hub nut by hand
    • Tighten the hub nut preliminarily
  4. step : Reattaching the Wheel (6:12)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 95 - 100 foot-pounds of torque in a crossing or star pattern
    • Tighten the hub nut to 180 foot-pounds

Tools needed for replacement:

    General Tools

  • Assistant
  • Center Punch
  • Floor Jack
  • Hammer
  • Jack Stands
  • Pick

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench
  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 19mm Socket
  • 36mm Socket

  • Specialty Tools

  • Pickle Fork

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
Who is the manufacturer of this shaft. Where is it made?
Robert L on May 22, 2017

Vehicle Fit

  • 1999-2004 Honda Odyssey Passenger Side CV Axle Shaft Outer Front

This part replaces:

  • OE # 44305S0XA52
  • OE # 44305S0XA51
  • Hollander 447-60406R
Part #: 1AACV00102



How-to Video:

(07:09 min)