1ASFK06131-1998-99 Dodge Ram 1500 2500 Steering & Suspension Kit 12 Piece Set

Replaces

1999 Dodge Ram 1500 Truck 4 Wheel Drive Steering & Suspension Kit 12 Piece Set

1ASFK06131-1180800-1999
Guaranteed to fit: 1999 Dodge Ram 1500 Truck

Fit Details

  • Vehicle Drivetrain Configuration: 4 Wheel Drive

Part Details

  • Kit Includes: (2) Front Sway Bar Links
  • Kit Includes: (2) Front Lower Ball Joints
  • Quantity: 12 Piece Set
  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (2) Front Upper Ball Joints
  • Kit Includes: (2) Front Inner Tie Rods
  • Kit Includes: (2) Tie Rod Adjusting Sleeves

This part replaces:

  • Moog K8195T
  • Moog ES2012S
  • Moog K3134T
  • Moog ES3497
  • Moog K7280
  • Moog DS1458
  • Moog DS1457
  • Moog K7208T
  • OE # 5069117AA
  • OE # 52037600
  • OE # 52039185
  • OE # 52039263
  • OE # 52038665
FREE SAME DAY SHIPPING
Save 15%
List: $187.95 Save: $28.00
Part 1ASFK06131
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: PSA70028
Description
Vehicle Fit
Warranty & Shipping
How-To & Tools
Q&A

Part Details

  • Quantity:   12 Piece Set
  • Kit Includes:
      (2) Front Sway Bar Links
      (2) Front Lower Ball Joints
      (2) Front Outer Tie Rods
      (2) Front Upper Ball Joints
      (2) Front Inner Tie Rods
      (2) Tie Rod Adjusting Sleeves

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

Note: When replacing steering components, it is recommended to have a professional alignment performed on the vehicle afterwards. This will ensure proper tracking and even tire wear.

  1. step : Removing the Wheel (1:03)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Straighten the cotter pin on the axle nut with needle nose pliers
    • Remove the cap and washer from the axle nut
    • Loosen the axle nut with a 36mm socket and breaker bar
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Brake Rotor (2:29)
    • Remove 13mm bolts from the brake caliper
    • Pull the caliper aside and secure it out of the way with a bungee chord
    • Pull the rotor off
  3. step : Removing the Hub (3:17)
    • Spray rust penetrant around the contact points of the hub
    • Remove the three 13mm 12-point bolts from the hub
    • Pry off the washer from the axle (if you have one) with a pick
    • Tap the axle in with a hammer to free the splines from the hub
    • Tap the hub out of the spindle with a hammer
    • Remove the hub and dust shield
  4. step : Loosening the Tie Rod (4:56)
    • Remove the cotter pin from the tie rod castle nut with a pair of pliers
    • Remove the 19mm castle nut from the tie rod
    • Hit the edge of the spindle to release the stud
    • Release the tie rode from the spindle
  5. step : Removing the Lower and Upper Ball Joint (6:08)
    • Remove the cotter pins from the upper and lower ball joints
    • If the cotter pin breaker or gets stuck, punch the pin through with a punch and hammer
    • Remove the axle shaft from the housing
    • Insert rags or a glove to stop axle fluid from leaking
    • Remove the two 22mm castle nuts from the ball joints
    • Insert a pick fork between the upper ball joint and the spindle to release the ball joint
    • If needed, hit the bottom to release the spindle from the axle
    • Remove the upper ball joint with a ball joint press
    • Repeat the process for the lower ball joint
  6. step : Installing the Lower and Upper Ball Joint (11:36)
    • Remove the boots from the ball joints
    • Press the upper ball joint into the spindle with the ball joint press until it bottoms out into the slot on the axle
    • Insert the boot to the upper ball joint
    • Press the lower ball joint into the spindle with the ball joint press until it bottoms out into the slot on the axle
    • Insert the boot to the lower ball joint
    • Hand-tighten the lower ball joint castle nut
    • Hand-tighten the upper ball joint castle nut
    • Tighten the lower ball joint castle nut with a 32mm socket and ratchet
    • Tighten the upper ball joint castle nut with a 22mm socket and ratchet
    • Torque the upper ball joint nut to 75 foot-pounds
    • Torque the upper ball joint nut to 80 foot-pounds
    • Install the lower cotter pin with the longer end facing down over the stud
    • Cut the shorter leg off
    • Install the upper cotter pin with the longer end facing down over the stud
    • Cut the shorter leg off
    • Tighten the upper ball joint grease fitting with a 7mm wrench
    • Add grease to the ball joint until the boot swells without popping off the joint
    • Remove the rags blocking the axle fluid
    • Insert the axle into the differential
  7. step : Reinstalling the Tie Rod (15:41)
    • Insert the tie rod into the spindle
    • Tighten the 19mm castle nut
    • Torque the tie rod nut to 35 foot-pounds
    • Insert the new cotter pin into the tie rod
    • Bend the longer leg over the top of the stud
    • Cut the shorter leg
  8. step : Installing the Hub (16:37)
    • Insert the dust shield into place
    • Insert the hub into place
    • Tighten the 12-point 13mm bolts
    • Torque the hub bolts to 75 foot-pounds
  9. step : Installing the Rotor (17:27)
    • Insert the rotor onto the hub
    • Press the caliper onto the rotor
    • Tighten the two 13mm bolts to the caliper
    • Torque the caliper mounting bolts to 20 foot-pounds
  10. step : Reattaching the Wheel (18:07)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 110 foot-pounds in a crossing or star pattern
    • Torque the axle nut to 175 foot-pounds
    • Insert the axle nut cap into place
    • Insert a new cotter pin into place
    • Turn each end of the cotter pin to opposite sides of the nut

Tools needed for replacement:

    General Tools

  • Center Punch
  • Hammer
  • Pick

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Bungee Cord

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 19mm Socket
  • 13mm Socket
  • 36mm Socket
  • 22mm Socket

  • Specialty Tools

  • Ball Joint Press
  • Pickle Fork
  • Grease Gun

  • Wrenches - Metric

  • 7mm Wrench

Need help? Ask one of our Auto Experts
Need help? Ask one of our Auto Experts
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Will this product fit with a 5 inch full suspension lift?
Anthony S April 13, 2019
This kit will not work with a lift kit. The parts are for vehicles with the stock ride height.
Andra M April 14, 2019
Does these parts have grease fittings?
Jason F May 5, 2020
Thank you for your inquiry! Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions. They will not have grease fittings as they are not needed. Please let us know if you have any further questions, thank you.
Jessica D May 5, 2020

Fits the following Makes:

Year Make Model Description
1998-1999Dodge Ram 1500 Truck Dodge Ram 1500 Truck 4 Wheel Drive Steering & Suspension Kit 12 Piece Set
1998-1999Dodge Ram 2500 Truck Dodge Ram 2500 Truck 4 Wheel Drive with Light Duty Suspension Steering & Suspension Kit 12 Piece Set

Part Interchange

Brand Label Part Number
Chrysler 52037600
Chrysler 52039263
Chrysler 52039185
Chrysler 52038665
Chrysler 5069117AA
DIY Solutions SUS00089
DIY Solutions SUS00140
DIY Solutions SUS07504
DIY Solutions SUS07505
DIY Solutions SUS07481
DIY Solutions SUS06820
DIY Solutions SUS06697
MOOG DS1457
MOOG K3134T
MOOG ES3497
MOOG K7280
MOOG ES2012S
MOOG K8195T
MOOG DS1458
MOOG Chassis Products K7280
MOOG Chassis Products ES2012S
MOOG Chassis Products DS1457
MOOG Chassis Products DS1458
MOOG Chassis Products ES3497
MOOG Chassis Products K8195T
MOOG Chassis Products K3134T

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

FREE SAME DAY SHIPPING
TRQ
Brand #: PSA70028
Product Reviews
4.33/ 5.0
6 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
5
0
0
0
1
Shipping is TERRIBLE. Worst i have ever seen.
There was absolutely no packing inside this box, it was literally just the steering components inside a big box that was zip tied around the top and around the bottom. I dont know if you have a 3 year old packaging your stuff but jesus christ have some pride in your work. The parts are most likely damaged.
May 2, 2019
Suspension kit
Installed the kit and is working very well
May 13, 2019
Perfect
Recommend this! Was relatively easy to put on, just follow the way your front end looks on your truck. Hardest part was ball joints of course. But now the truck rides perfect!
June 28, 2019
Great product
100% satisfied. Great parts and great quality.
September 24, 2019
Great deal
Bought this kit for friend who does not have internet access. What a good deal. saved him over half of price from local parts store. Good quality, easy fitment. Great vendor, good communication fast delivery, and saved my friend $150. Home run! Thanks 1A auto Joe Kalamazoo
April 3, 2020
1999 Dodge Ram 1500
Everything fit like factory
August 16, 2020
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET

Dodge is a registered trademark of FCA US LLC. 1A Auto is not affiliated with or sponsored by Dodge or FCA US LLC. See all trademarks.

1998-99 Dodge Ram 1500 2500 Steering & Suspension Kit 12 Piece Set TRQ PSA70028-1ASFK06131 does not fit your:


Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a 1999 Dodge Ram 1500 Truck with these options.