1ASFK06131-1998-99 Dodge Ram 1500 2500 12 Piece Steering & Suspension Kit
false

Replaces

1998 Dodge Ram 1500 Truck 4 Wheel Drive 12 Piece Steering & Suspension Kit

Guaranteed to fit 1998 Dodge Ram 1500 Truck

FREE SAME DAY SHIPPING
Save 29%
List: $246.95 Save: $72.00
Part 1ASFK06131
In Stock


Orders must be placed by 2pm ET
Delivery options for:

Estimated Arrival Cost


Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

TRQ
Brand #: PSA70028

Frequently bought together

Description

Vehicle Fit

Warranty & Shipping
How-To & Tools

Part Details

  • Quantity:   12 Piece
  • Kit Includes:
      (2) Front Sway Bar Links
      (2) Front Lower Ball Joints
      (2) Front Outer Tie Rods
      (2) Front Upper Ball Joints
      (2) Front Inner Tie Rods
      (2) Tie Rod Adjusting Sleeves

Install Tip: When replacing steering components, have a professional alignment performed afterwards.  This ensures proper tracking and even tire wear.

Our steering and suspension components are pre-greased and sealed for long life and do not require the extra maintenance typically required by greaseable versions.

No modifications, all the parts needed in one kit
Direct fit - easy install, pre-greased, no maintenance required
Improved ride comfort and longer life

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by our limited lifetime warranty. In the event this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.

FREE Shipping is standard on Orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii, Alaska and US Territories.

Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, or Canada for this item.

Expedited is available on checkout to the United States, excluding Alaska, Hawaii and US Territories.

How to Replace Front Upper & Lower Ball Joints 90-01 Jeep Cherokee

Created on: 2021-01-16

Check out this video to learn how you can replace the upper and lower ball joints on your 90-01 Jeep Cherokee.

  1. step 1 : Removing the Wheel
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Straighten the cotter pin on the axle nut with needle nose pliers
    • Remove the cap and washer from the axle nut
    • Loosen the axle nut with a 36mm socket and breaker bar
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step 2 : Removing the Brake Rotor
    • Remove 13mm bolts from the brake caliper
    • Pull the caliper aside and secure it out of the way with a bungee chord
    • Pull the rotor off
  3. step 3 : Removing the Hub
    • Spray rust penetrant around the contact points of the hub
    • Remove the three 13mm 12-point bolts from the hub
    • Pry off the washer from the axle (if you have one) with a pick
    • Tap the axle in with a hammer to free the splines from the hub
    • Tap the hub out of the spindle with a hammer
    • Remove the hub and dust shield
  4. step 4 : Loosening the Tie Rod
    • Remove the cotter pin from the tie rod castle nut with a pair of pliers
    • Remove the 19mm castle nut from the tie rod
    • Hit the edge of the spindle to release the stud
    • Release the tie rode from the spindle
  5. step 5 : Removing the Lower and Upper Ball Joint
    • Remove the cotter pins from the upper and lower ball joints
    • If the cotter pin breaker or gets stuck, punch the pin through with a punch and hammer
    • Remove the axle shaft from the housing
    • Insert rags or a glove to stop axle fluid from leaking
    • Remove the two 22mm castle nuts from the ball joints
    • Insert a pick fork between the upper ball joint and the spindle to release the ball joint
    • If needed, hit the bottom to release the spindle from the axle
    • Remove the upper ball joint with a ball joint press
    • Repeat the process for the lower ball joint
  6. step 6 : Installing the Lower and Upper Ball Joint
    • Remove the boots from the ball joints
    • Press the upper ball joint into the spindle with the ball joint press until it bottoms out into the slot on the axle
    • Insert the boot to the upper ball joint
    • Press the lower ball joint into the spindle with the ball joint press until it bottoms out into the slot on the axle
    • Insert the boot to the lower ball joint
    • Hand-tighten the lower ball joint castle nut
    • Hand-tighten the upper ball joint castle nut
    • Tighten the lower ball joint castle nut with a 32mm socket and ratchet
    • Tighten the upper ball joint castle nut with a 22mm socket and ratchet
    • Torque the upper ball joint nut to 75 foot-pounds
    • Torque the upper ball joint nut to 80 foot-pounds
    • Install the lower cotter pin with the longer end facing down over the stud
    • Cut the shorter leg off
    • Install the upper cotter pin with the longer end facing down over the stud
    • Cut the shorter leg off
    • Tighten the upper ball joint grease fitting with a 7mm wrench
    • Add grease to the ball joint until the boot swells without popping off the joint
    • Remove the rags blocking the axle fluid
    • Insert the axle into the differential
  7. step 7 : Reinstalling the Tie Rod
    • Insert the tie rod into the spindle
    • Tighten the 19mm castle nut
    • Torque the tie rod nut to 35 foot-pounds
    • Insert the new cotter pin into the tie rod
    • Bend the longer leg over the top of the stud
    • Cut the shorter leg
  8. step 8 : Installing the Hub
    • Insert the dust shield into place
    • Insert the hub into place
    • Tighten the 12-point 13mm bolts
    • Torque the hub bolts to 75 foot-pounds
  9. step 9 : Installing the Rotor
    • Insert the rotor onto the hub
    • Press the caliper onto the rotor
    • Tighten the two 13mm bolts to the caliper
    • Torque the caliper mounting bolts to 20 foot-pounds
  10. step 10 : Reattaching the Wheel
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 110 foot-pounds in a crossing or star pattern
    • Torque the axle nut to 175 foot-pounds
    • Insert the axle nut cap into place
    • Insert a new cotter pin into place
    • Turn each end of the cotter pin to opposite sides of the nut

Tools needed for replacement

  • General Tools

    Hammer

    Pick

    Center Punch

  • Materials, Fluids, and Supplies

    Rust Penetrant

    Bungee Cord

  • Pliers, Cutters & misc Wrenches

    Needle nose pliers

  • Ratchets & Related

    A Piece of Pipe (for leverage)

    Socket Extensions

    Torque Wrench

    Ratchet

  • Screwdrivers & Related

    Pry Bar

  • Sockets - Metric

    13mm Socket

    19mm Socket

    36mm Socket

    22mm Socket

  • Specialty Tools

    Ball Joint Press

    Grease Gun

    Pickle Fork

  • Wrenches - Metric

    7mm Wrench

Installation Video
Watch video

Fits these Makes

Year Make Model Description
1998-1999Dodge Ram 1500 Truck Dodge Ram 1500 Truck 4 Wheel Drive 12 Piece Steering & Suspension Kit
1998-1999Dodge Ram 2500 Truck Dodge Ram 2500 Truck 4 Wheel Drive with Light Duty Suspension 12 Piece Steering & Suspension Kit

Part Interchange

Brand Label Part Number
Chrysler 52037600
Chrysler 52039263
Chrysler 52039185
Chrysler 52038665
Chrysler 5069117AA
DIY Solutions SUS00089
DIY Solutions SUS00140
DIY Solutions SUS07504
DIY Solutions SUS07505
DIY Solutions SUS07481
DIY Solutions SUS06820
DIY Solutions SUS06697
MOOG DS1457
MOOG K3134T
MOOG ES3497
MOOG K7280
MOOG ES2012S
MOOG K8195T
MOOG DS1458
MOOG Chassis Products K7280
MOOG Chassis Products ES2012S
MOOG Chassis Products DS1457
MOOG Chassis Products DS1458
MOOG Chassis Products ES3497
MOOG Chassis Products K8195T
MOOG Chassis Products K3134T

This item may be interchangeable with parts from other brands with the above part numbers. This information is provided only for reference and does not guarantee that the item you are purchasing is identical to parts with part numbers from the brands listed above. To confirm that this item fits your vehicle, use the above "Check Vehicle Fit" option.

TRQ
Brand #: PSA70028
Product Reviews
4.29/ 5.0 7
Shipping is TERRIBLE. Worst i have ever seen.
Anthony
May 2, 2019
There was absolutely no packing inside this box, it was literally just the steering components inside a big box that was zip tied around the top and around the bottom. I dont know if you have a 3 year old packaging your stuff but jesus christ have some pride in your work. The parts are most likely damaged.
Suspension kit
H
May 13, 2019
Installed the kit and is working very well
Perfect
C
June 28, 2019
Recommend this! Was relatively easy to put on, just follow the way your front end looks on your truck. Hardest part was ball joints of course. But now the truck rides perfect!
Great product
Austen
September 24, 2019
100% satisfied. Great parts and great quality.
Great deal
Tachacardic
April 3, 2020
Bought this kit for friend who does not have internet access. What a good deal. saved him over half of price from local parts store. Good quality, easy fitment. Great vendor, good communication fast delivery, and saved my friend $150. Home run! Thanks 1A auto Joe Kalamazoo
1999 Dodge Ram 1500
WILLIAM
August 16, 2020
Everything fit like factory
Worked well
MIKE
December 26, 2020
Everything fit perfectly, no hassles. Not the company's fault at all, but be sure to check all pieces made it through shipping before starting install. Because of the very heavy weight and awkward shape, the packages take a beating in the mail.
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
Will this product fit with a 5 inch full suspension lift?
April 13, 2019
10
This kit will not work with a lift kit. The parts are for vehicles with the stock ride height.
April 14, 2019
Does these parts have grease fittings?
May 5, 2020
10
Thank you for your inquiry! Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions. They will not have grease fittings as they are not needed. Please let us know if you have any further questions, thank you.
May 5, 2020
Customer service

877-844-3393

Monday - Friday 8:00am - 9:30pm ET
Saturday - Sunday 8:00am - 4:30pm ET

Dodge is a registered trademark of FCA US LLC. 1A Auto is not affiliated with or sponsored by Dodge or FCA US LLC. See all trademarks.

1998-99 Dodge Ram 1500 2500 12 Piece Steering & Suspension Kit TRQ PSA70028-1ASFK06131 does not fit your:



Same Day Shipping

Need your part faster? Choose expedited shipping at checkout.

Guaranteed To Fit

Highest quality, direct fit replacement auto parts enforced to the strictest product standards.

USA Customer Support

Exceeding customers' expectations, our team of passionate auto enthusiasts are here to help.

Instructional Video Library

Thousands of how-to auto repair videos to guide you step-by-step through your repair.

Before proceeding,

select your Vehicle, to verify this Part will fit.

This part will only fit a 1998 Dodge Ram 1500 Truck with these options.