Replaces
This part doesn’t fit a . Select from parts that fit.
1A Auto Lifetime Warranty
Frequently bought together
Part Details
This window regulator is a high quality aftermarket part that meets or exceeds the performance of the original. Subjected to extensive testing and quality control standards, allows us to offer this regulator with our superior warranty!
Item Condition:
New
Attention California Customers:
WARNING: This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
Created on:
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike from 1A Auto. I hope this how-to video helps you out, and next time you need parts for your vehicle, think of 1AAuto.com. Thanks.
This is part two of a two part series installing a window regulator with a motor into a 2000 Lincoln Town Car. It's the same as any '98 to '02. For these vehicles, we sell the regulator with motor and without motor. This is for installing the regulator with a motor. The tools you'll need, we'll just a quick look at that again.
The one with the black rail is my original. The new one from 1A Auto. You can see the one from 1A Auto is going to go in exactly the same. Some things: it's been beefed up so it's a little larger in diameter on the wheel up here. That allows it to spin a little slower and has less wear. It's just going to go in there. You're going to have to bolt it in. It's going to fit the same. It has the same pigtails with plugs all the same. I'm bolting it in.
First, you've just kind of got to stuff it in there. Bring it up, and the first thing is to hang it from these bolts up here. You can look down here. The easiest way to see the place for your motor is with the plate side to the inside of the door. Hang it up from here first. There is a locating slot right here. Push your motor up and in. Push your motor up aligned with that hole there. Slide it up. You can see there's the tab right there. This is all lined up now. What I'm using are some M6. They're 12mm in length little bolts with nuts that have a serrated side to them. These little serrations, they kind of dig into the metal and hold them in place.
This tab is holding my motor in place. Reach in with the crack-it-up and put that bolt through. Start another one on the back side. I'm going to speed it up here as I put the other two nuts and bolts in, and then tighten them up. Unfortunately, with this angle, you don't see much except the great shot of the logoed sweatshirt there. Again, all I do is I put those bolts in, tighten them up, and then move on to the next step. I'm going to move through this at a little higher speed as well. Put those two nuts at the top that hold on to the studs. They're just like the original.
You want to put the nuts on there, but you don't want to tighten them up all the way. What you're going to want to do is run the window up and down. You'll see that. You put those both on, but don't tighten them up all the way. It's the same thing at the bottom. Use some M6 12mm bolts and nuts, and secure the bottom. Again, don't tighten them up until later.
Now I take our lead, put it through, and connect it. You can see I've just plugged my switch back in. We've just moved this down until we can easily see the holes. I can see the hole right here easily, and then I can see the hole through here, through this hole here. I'll take the window. Front in first. Slide it right down there and put the nose down. Make sure you've got the front in the track and the rear in the track. Slide it down to the regulator.
Now, you want 2 1/2mm bolts. It's generally easier to line up this front one that's a little higher to get to. Put the bolt in. I'm going to put my nut in my socket here, and then start it. You can see in my rear one. I'll speed this up as I use my socket and ratchet. I actually use a 10mm wrench on the inside. That's what I'm putting on there, on the other side of the window. Hold it with a 10mm wrench, and then tighten it up with my socket and ratchet. Then do the front one as well.
Now with the key on, run your window up and down a little a couple times. Probably with it right up there. Tighten up this upper one, tighten up this one, then retighten my lower ones. Now I'm going to move a little quicker. Take that switch back apart or unplug it. Put that piece of weatherstrip back on the inside. Then we'll fast-forward through putting the door panel back on. If you did want to see the door panel, if you want to see it in regular speed, just check out our other Lincoln Town Car videos, and you'll see a front-door panel installation and removal.
We hope this video helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the Internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing or maintaining your vehicle. I'm going to use my 20-plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly: that's going to save you time and money. Thank you and enjoy the video.
In this video, we're going to show you how to replace the window regulator and motor in this 2000 Lincoln Town Car, same as any '98-'02. We sell these regulators with motor and without motor; this video shows you how to replace them when you're replacing both the regulator and the motor at the same time. Tools you'll need are Phillips and flat blade screwdrivers; T30 Torx driver, hammer, punch and chisel; a drill with a 5/16 drill bit; 10mm socket and ratchet with extension which could vary and some needle nose pliers.
Door panel removal: it's fairly simple. On this vehicle this door panel's been taken apart a bunch of times so some of the fasteners may be different for you. For example, it has a screw here, which I believe most cars probably don't. The reason it has a screw here I believe is because so many of the pins in behind to hold it are broken. The way you'll want to start is to remove your door lock knob just by unscrewing it then in under here should be two . on this vehicle, they're Phillips screws . and you just kind of put your screwdriver up under there. Now there's another Phillips screw up in here. This pulls out and then right in here, you'll see there's another Phillips screw. It goes into the door panel. As you can tell I've been fast forwarding when I get to the monotonous stuff so you remove that screw and then there's another screw next to the rear side of the pull. Then at the bottom there are two more Phillips screws. It's kind of a little indent in the carpet, just put your screwdriver in there, twist it a little bit and you'll get the screw. This car has a little Torx screw here, I'm not sure if this is supposed to be there or not. I'll remove it. This may not be on all cars. Then there is another screw here but this is broken on my car so I know there's no screw in there. Then, what there is, is there's a series of clips, so you want to work your hand underneath here and there's one clip right here and you get your hand as close to those . you can slide your hand underneath and you slide it over and you feel it getting tighter and tighter and then you give a good pull and get that clip out and then come up here on the top and give it a good pull on the clip there and then on these vehicles there's more clips, there's clips in the middle and more on the edge but like I said, this vehicle's been apart a few times.
Actually before you pull the door panel off you want to pull your window switch up in the front and then pull it out and then there's a series of harnesses that just have little tabs, you press the tab, pull the harness down, this gray one, tab, pull it down, tab here on the black one and then tab here for the brown one. Pull the panel away and there's a few more harness connections back here, a couple of small harnesses with a black and white connector. Press the little button here, and pull that apart. The blue connector here that has a tab on it that you pull the wires in the blue connector, and pull the tab out. It's hard to see. There's a gray connector here, again, big tab, pull that apart. Looks like this screw's not quite all the way out.
Your door panel is off. You can see here, I'm holding back the water shield, you may have noticed on the other clip that on this car somebody has just cut the water shield, there should be a shield covering that whole large open area, you want to pull your water shield back carefully because you do want to save it because it does protect your door panel from getting aged too quickly by water and dirt.
To remove your power window motor your lead is right here, press on this tab, pull the lead up and out and there's three T30 Torx screws right here and you remove the bottom two and you loosen the top one. Once you loosen that top one, reach in behind and you slide the whole motor and cable assembly out and you pull it all the way out to here. Next I'll finish removing this. The motor comes off.
Now you can slide your window down and you can access this rivet here and this one through here so your rivets that hold the regulator to the window is right there and then I can see one right through there. Now I'm going to take a drill with a 5/16th bit and I'm going to slowly drill into these rivets; I don't want to go too fast because I don't want them to spin. That one comes off, and they're aluminum so they do come off fairly easy. That one's off. Now I can take my window, the window now separates from the regulator. You'll want to pull this piece of weatherstrip right up and off. You're going to want to remove the window and what you do to do that is slide the front down a ways and then push it out towards the outside of the car and then you pull the window diagonally out and back to front and then your rivets will probably get stuck on the little wiring harnesses in here a little bit and it goes to the back and the window comes out.
On the window you'll have these rivets. With a pair of needle nose pliers, carefully just pop them out. The regulator is held at the bottom by two rivets here. With a nice punch, pointed end and a good size hammer, put it right into the middle of the rivet and you can see I knocked the middle of the rivet right through and again with the drill nice and easy. My rivet's starting to spin a little bit so the cold chisel and there's not much left to these rivets so knocked one off, and knocked the other one off. Now the regulator's still held in here by two 11mm nuts so I've got a socket, ratchet and extension. Just use a little fast forward here as I remove those two nuts and one of them ended up actually being a 10mm nut so your, the sizes could vary on your vehicle as well, it appears this car's been apart before. Now bring those there, comes right out and now just like the lower rivets you drill. I'm just going to use my drill and I'm going to drill out the three rivets that hold the bracket that hold the window motor and those of you that are keen, you'll see that the regulator is actually back in the door that's just because you can do this either way, you can drill the rivets off for the motor first and take the whole assembly out, or you can take the regulator all apart and then drill the rivets and pull the bracket out. You see I drill it and now I will use the chisel and knock the rivets off and then I can take that bracket out or as I said, if you want to remove the window motor and regulator at the same time you can do it that way. The one with the black rail is my original, new one from 1A Auto. You can see the one from 1A Auto is going to go in exactly the same so the thing is it's been beefed up; it's a little larger diameter wheel up here; that allows it to spin a little slower and has less wear and it's just going to go in there it's going to bolt in or you're going to have to bolt it in and it's going to fit the same, has the same pigtail so it plugs in all the same. After that beautiful comparison we're going to stop here and if you want to see the second part of this video which is installing the new regulator with motor, please check out the video with the same title, just has part two in it.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the Internet. Please feel free to call us toll-free, 888-844-3393. We're the company that's here for you on the Internet and in person.
Tools used
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. Hi, I'm Mike Green, I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20 plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly that's going to save you time and money. Thank you and enjoy the video.
This video is going to be part one of a two part series, replacing a window regulator in this 2000 Lincoln Town car, same as any '98 to '02. We offer the window regulator with motor and without motor, this video covers replacing your window regulator without the motor. The tools you'll need are Philip's and flat blade screwdrivers, T30 Torx driver, a hammer with a punch and a chisel, a drill with a 5/16 drill bit, 10mm socket with ratchet and extension and there's a little star there because your vehicle may vary, it may be 10 or 11mm and needle nose pliers. Door panel removal, it's fairly simple. On this vehicle, this door panel has been taken apart a bunch of times so some of the fasteners may be different for you as well as the ... for example, it has a screw here, which I believe most cars probably don't and the reason it has a screw here I believe is because so many of the pins in behind that hold it are broken. Where you want to start is remove your door lock knob just by unscrewing it and then in under here should be two, on this vehicle they're Philip's screws, and you kind of just put your screwdriver up under there. Now, there's another Philip's screw up in here. Then this pulls out. Then right in here you'll see there's another Philip's screw that goes into the door panel. As you can tell I've been fast forwarding when I just get to the monotonous stuff, so you remove that screw and then there's another screw next to the rear side of the pole. Then at the bottom, there's two more Philip's screws, there's a little indent in carpet, just put your screwdriver in there, twist a little bit and you'll get to the screw.
This car has a little Torx screw here, I'm not sure if it's supposed to be there or not. I'll remove it, this may not be on all cars. Then there is another screw here but this is broken on my car so I know there's no screw in there and then what there is a series of clips so you want to work your hand underneath here and there's one clip right here and you want to get your hand as close to those... you can slide your hand underneath and you slide it over and you'll feel it getting tighter and tighter. Then you give a good pull and get that clip out. Then come up here on the top and give that a good pull on that clip there and then on these vehicles there's more clips, there's clips in the middle and more on the edge but like I said this vehicle has been apart a few times. Before you pull the door panel off, you want to pull your window switch up in the front and then pull it out and then there's a series of harnesses that just have a little tabs, you press the tabs, pull the harness down. Gray one tab, pull it down, a tab here on the black one, and then a tab here for the brown one. Now, pull the panel away and there's a few more harness connections back here. A couple of small harnesses with a black and white connector, press a little button here, pull that apart. There's a blue connector here that has a tab on it that you pull the wires of the blue connector, pull the tab out. It's hard to see.
There's a gray connector, again a big tab, pull it apart. Oops, it looks like the screw isn't quite all the way out. Your door panel is off. Okay, so you can see here I'm holding back the water shield, you may have noticed on the other clip that on this car somebody has cut the water shield, there should be a shield covering that whole large open area. You want to pull your water shield back carefully because you do want to save it because it does protect your door panel from getting aged too quickly by water and dirt. To remove your power window motor, if your lead is right here, press on this tab, pull the lead up and out and then there's three T30 Torx screws right here and you remove the bottom two and you loosen the top one. Once you loosen that top one, reach in behind and you slide the whole motor and cable assembly out. Pull it all the way to here and I'll actually finish removing this. Then the motor comes off. Now you can slide your window down and you can access this rivet here and this one through here. Your rivets that hold your regulator to the window is right there and then I can see one right through there. Now, I'm going to take a drill with a 5/16 bit and going to slowly drill into these rivets and I don't want to go to fast because I don't want them to spin. That one comes off. They are aluminum so they do come off fairly easy. Now that one's off.
Now I can take my window, the window now separates from the regulator. You'll want to pull this weather strip right up and off and you're going to want to remove the window and what you need to do that is slide the front down a ways and then push it out towards the outside of the car and then you just pull the window diagonally out. Go back to the front and your rivets will probably get stuck on the little wiring harnesses in here a little bit. Move those to the back and the window comes out. Now the regulator is held at the bottom by two rivets here, a nice punch, pointed end and a good size hammer, put it right in the middle of the rivet and you can see I knocked the middle of rivet right through. Again with the drill, nice and easy. You can see my rivet started to spin a little bit so get a Cole chisel and there not much left to these rivets so ... knock one off and knock the other one off. Now the regulator is still held in here by two 11mm nuts so I've got a socket, ratchet and a extension. I'm just going to fast forward this and actually on this vehicle looks like it was taken apart before, one nut was 11mm and one was 10mm so yours could either have 10 or 11mm nuts. Now bring the regulator down and it comes right out. Okay, so we're going to end right here, if you want to see the re-installation just search for the same video just with part two in title rather than part one.
We hope this helps you out. Brought to you by www.1AAuto.com, your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free 888-844-3393. We're the company that's here for you on the internet and in person.
