Replaces

1998-02 Wheel Bearing & Hub Assembly Front Timken 513202 - TKSHF00126

TIMKEN WHEEL BEARING & HUB ASSEMBLY: 513202

This replacement hub & bearing assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • Replaces dealer part number: F7AZ-1104-AC, F7AZ1104AC
  • Direct replacement
  • Built to strict quality control standards
  • New wheel studs installed
  • Fits models with ABS (Anti-Lock Brakes) only

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hub & bearings are all tested prior to shipping.

Fit Guaranteed

  • This hub & bearing will install just as your original does. You can use your existing hardware.
  • Save time and money with this direct fit hub bearing assembly. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

Note: These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel (1:04)
    • Pry off the center cap
    • Use the hub cap key to remove the hub cap.
    • Loosen the lug nuts.
    • Raise and secure the vehicle
    • Remove the lug nuts and the wheel.
    • For extra security, put the wheel under your car should your jack stands fail.
  2. step : disassemble the brakes (1:45)
    • Remove the 13 mm caliper bolts.
    • Use a screwdriver to pry between the caliper and caliper bracket to pry the caliper up and off.
    • Secure the caliper with wire ties up out of the way.
    • Using an 18 mm socket and a breaker bar or pipe for leverage, remove the caliper bracket bolts.
    • Remove the brake disc.
  3. step : Un-install the hub (3:56)
    • Remove the dust cover from the hub nut.
    • Using a breaker bar, maybe even a pipe for leverage in addition, remove the 35 mm hub nut.
    • Remove the hub.
  4. step : Install the new hub (4:48)
    • Clean up the area to insure a smooth fit.
    • Put the hub on, and replace the hub nut and torque it to 220 ft lbs.
  5. step : Reassemble the brakes (5:55)
    • Put the brake rotor/disc back on the hub.
    • Examine the brake rotor/disc for gouges or signs of excessive wear.
    • Replace the rotor if needed, remember to clean the rotor with warm soapy water or brake cleaner before installation, and prevent contact with oil and grease.
    • Check the condition of the brake pistons; make sure they slide in and out smoothly and freely.
    • Mount the caliper brackets and torque the 18 mm bolts to 90 ft lbs.
    • Check the condition of your brake pads and install new ones if needed.
    • Slide the brake pads into the brackets.
    • Compress the caliper and slide it onto the bracket and pads.
    • Bolt the caliper in, and torque the 13 mm bolts to 15-16 ft lbs.
  6. step : Replace the wheel (8:30)
    • Reinstall the small center cap and hub cap keeper.
    • Replace the lug nuts and lower the car, torque them in a star pattern to 100 ft lbs.
    • Put the hub cap back on and replace the safety nut and the final center cap back in place.
    • Place your hub cap key in back in your glove box for safekeeping.
    • Make sure you pump your brakes a few times before road testing to recompress the calipers.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Wire Brush
  • Chisel
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Wire Ties
  • Anti-Seize Grease
  • Rust Penetrant

  • Ratchets & Related

  • Ratchet
  • Socket Extensions
  • A Piece of Pipe (for leverage)
  • 1/2 Inch Breaker Bar
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 18mm Socket
  • 35mm Socket
  • 13mm Socket
  • 21mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1998-2002 Ford Crown Victoria Front Wheel Bearing & Hub Assembly for Models with ABS Brakes Timken 513202
  • 1998-2002 Lincoln Town Car Front Wheel Bearing & Hub Assembly for Models with ABS Brakes Timken 513202
  • 1998-2002 Mercury Grand Marquis Front Wheel Bearing & Hub Assembly for Models with ABS Brakes Timken 513202

This part replaces:

  • Timken 513202
  • Hollander 538-01434B
  • OE # F7AZ 1104 AC
Only 4 left in stock
Part #: TKSHF00126

Ships Same Day for orders placed by 4 P.M. ET

Timken
Brand #: 513202

How-to Video:

(09:45 min)