Replaces

1998-02 Chevy Camaro Pontiac Firebird Brake Kit - 1APBS00002

This performance brake rotor & posi pad set is just what you need to get your vehicle stopping in good order again!

Brake Pad Specifications:

  • Premium Posi Semi Metallic brake pads
  • 4 Piece Front brake pad set
  • Includes shims
  • Direct replacement

Brake Rotor Specifications:

  • Comes as a matched pair
    • Includes both LH (Driver) & RH (Passenger) Side FRONT
  • Cross drilled, Slotted, And Zinc Coated
  • Fits 5 Stud Wheels
  • 11.92" Diameter
  • Vented

Premium Positive Molded Brake Pads Features and Benefits:

  • The very same manufacturing process the original equipment manufacturers use
  • High density friction material for long pad life
  • Less resin content virtually eliminates brake fade and glazing
  • Reduced dusting for both Ceramic and Semi-metallic materials
  • Quality multi-layered shims and pad chamfering provide smooth and quiet braking
Positive Mold Technology

Positive Mold Technology improves durability and performance by allowing for even wear. High density, low resin friction material virtually eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

OE Grade Multi-Layer Shim

OE Grade Multi-Layer Shim helps reduce vibration and noise

Environmentally Compliant

Certified Environmentally Compliant to "Better Brake Law" standards

Zinc Coated

Zinc Coated to help reduce rust and corrosion for a longer-lasting and better looking rotor

"True" Non-Interference Vane Design

"True" Non-Interference Vane Design retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots are machined to remove brake dust and expel gasses during hard braking

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Step 1: Removing the Brake Caliper (1:12)
    • Pry center cap or hubcap to access and remove the lug nuts.
    • Jack up the car and remove the wheel.
    • Place a screw driver or pry bar into the hole on the caliper and pry out so that the piston drops into the caliper.
    • Undo the two 15 mm bolts on the back of the caliper.
    • Pull caliper off, using a screw driver to pry it off if necessary.
    • Secure caliper bracket safely to avoid stressing the brake line.
  2. step : Step 2: Removing the Caliper Bracket and rotor (3:08)
    • Pry brake pads out of the caliper bracket.
    • Remove the two 15 mm bolts on the back side of the caliper bracket (use pipe with the ratchet for more leverage).
    • Remove bracket and rotor.
  3. step : Step 3: Reinstallation of Brake Caliper (4:17)
    • Replace rotor and secure with a lug nut.
    • Replace the caliper bracket and tighten bolts to 90ft/lbs.
    • Remove caliper bracket slides and clean with a wire brush.
    • Slide brake pads into place.
    • Pull caliper down and use a c-clamp to push the piston all the way into the caliper.
    • Place the caliper back on to the bracket.
    • Clean caliper bolts and add small amount of oil.
    • Replace caliper bolts. Torque them to 50ft/lbs.
    • Remove lug nut and replace wheel.
    • Tighten lug nuts in a star pattern and replace cap.
    • Before driving, pump brakes until pedal goes solid.

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Wire Brush

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 15mm Socket
  • 19mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1998-2002 Chevy Camaro Front Premium Posi Semi-Metallic Cross Drilled & Slotted Zinc Coated Performance Brake Kit
  • 1998-2002 Pontiac Firebird Front Premium Posi Semi-Metallic Cross Drilled & Slotted Zinc Coated Performance Brake Kit
Part #: 1APBS00002



How-to Video:

(09:13 min)