Replaces

1998-02 Brake Rotor Pair Nakamoto 54060-DSZ - 1APBR00330

Part Details

  • Front Brake Rotor Specifications:
    12.44" (316mm)
    Vented
    5 Lug
  • Brake Rotor Type: Cross Drilled & Slotted
  • Quantity: Pair
  • Brake Rotor Coating: Zinc Coated
  • Product Line: Performance

Specifications:

  • Comes as a matched Pair
    • Includes LH (Driver Side) & RH (Passenger Side) Front
  • Cross drilled, Slotted, And Zinc Coated
  • Direct replacement
  • Fits 5 Stud Wheels
  • 12.42" (316mm) Diameter
Zinc Coated

Helps reduce rust and corrosion for a longer-lasting and better looking rotor.

"True" Non-Interference Vane Design

Retains the structural integrity of the rotor

CNC Cross Drilled and Slotted

Precision-Rounded End Slots remove brake dust and expel gasses during hard braking.

Cross Drilled Holes improve ventilation and cooling for less brake fade and more positive stopping power.

Item Condition: New

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (1:06])
    • Pry off the center cap with a flat blade screwdriver
    • Retrieve the center safety bolt key from the glove box
    • Remove the center safety bolt with the key
    • Pry off the wheel cover with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Inspecting the Brakes (1:44)
    • Turn the rotor by hand or turn the steering wheel to turn the rotor
    • Check for gouges on both sides of the rotor
    • Check the thickness of the brake pads
    • Check the brake pad wear indicator
  3. step : Removing the Brake Pads (2:41)
    • Remove the two 13mm bolts from the brake caliper
    • Pry the caliper off with a flat blade screwdriver
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
  4. step : Removing the Brake Rotor (3:55)
    • Remove the two 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Pull the rotor off
  5. step : Installing the New Brake Rotor (5:14)
    • Slide the rotor on
    • Thread one lug nut by hand to hold the rotor in place
    • Clean the caliper bracket with a wire brush
    • Make sure the caliper bracket slides move smoothly
    • Put the bracket back into place
    • Start the 18mm bolts by hand
    • Tighten the bolts to 90 foot-pounds of torque
  6. step : Installing the New Brake Pads (6:51)
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Install the new brake pads into the bracket with the notches on the upper side
    • Put the caliper on
    • Thread bolts by hand
    • Tighten bolts to between 15 - 16 foot-pounds
  7. step : Reattaching the Wheel (8:59)
    • Turn the wheels straight
    • Remove the placeholder lug nut
    • Slide the wheel into place
    • Put on the wheel cover bracket
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the wheel cover
    • Put the center safety bolt in with the key
    • Push on the center cap
  8. step : Testing the Brakes (9:44)
    • Return the center safety bolt key to the glove box
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Large C-Clamp
  • Wire Brush
  • Jack Stands
  • Floor Jack

  • Ratchets & Related

  • Ratchet
  • A Piece of Pipe (for leverage)
  • 1/2 Inch Breaker Bar
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 18mm Socket
  • 13mm Socket
  • 21mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

Year Make Model Description
1998-2002Ford Crown Victoria Ford Crown Victoria Front Brake Rotor Pair Cross Drilled & Slotted Zinc Coated Performance Nakamoto
1998-2002Lincoln Town Car Lincoln Town Car Front Brake Rotor Pair Cross Drilled & Slotted Zinc Coated Performance Nakamoto
1998-2002Mercury Grand Marquis Mercury Grand Marquis Front Brake Rotor Pair Cross Drilled & Slotted Zinc Coated Performance Nakamoto

This part replaces:

  • Nakamoto 54060-DSZ
Part #: 1APBR00330


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Nakamoto
Brand #: 54060-DSZ

How-to Video:

(10:28 min)