Replaces

1998-01 Nissan Altima Window Regulator Pair - 1AWRK00127

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Regulator Option:   with Motor
  • Quantity:   Pair
  • Operation:   Power

Specifications:

  • Driver and Passenger Front
  • Assembly includes motor and regulator
  • 100% tested prior to leaving the factory

Please Note: These window regulators are high quality aftermarket parts that meets or exceeds the performance of the original. They have been subjected to extensive testing and quality control standards. That is why we offer these regulators with our superior warranty!

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Lead and Lead Compounds, which are known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Door Panel (0:42)
    • Pry off the mirror base panel with a flat blade screwdriver
    • Pry off the switch panel with a flat blade screwdriver
    • Disconnect the window switch wiring harness
    • Pry off the trim piece inside the door pull with a flat blade screwdriver
    • Remove the Phillips head screw from the door pull
    • Pull out the door pull cover by hand
    • Pry off the door handle bezel with a flat blade screwdriver
    • Pull the door panel off by hand
    • Lift the door panel up and off
    • Remove the two Phillips head screws from the door speaker
    • Remove the Phillips head screw from the door handle
    • Remove the two Phillips screws from the door bracket
    • Peel back the water shield carefully
  2. step : Removing the Window Regulator (2:26)
    • Remove the four 10mm bolts from the door brace
    • Remove the brace
    • Lower the window by hand
    • Remove the two 10mm bolts from the window track
    • Raise the window by hand
    • Tilt the window and pull it out of the door
    • Disconnect the window motor lead
    • Pull the motor wiring harness away from the door
    • Remove one of the 10mm bolts from the top of the regulator
    • Loosen the other 10mm bolt from the top of the regulator
    • Remove the two 10mm bolts from the bottom of the regulator
    • Remove the three 10mm bolts from the window motor
    • Feed the motor wiring harness through the door
    • Pull the regulator and motor out through the door
  3. step : Installing the New Window Regulator (4:36)
    • Remove the 10mm bolt from the old regulator
    • Insert the 10mm bolt into the new regulator
    • Slide the new regulator into the door
    • Hang the regulator by its top bolt
    • Line up the window motor
    • Pull the motor wiring harness through the door
    • Connect the motor wiring harness
    • Start the three 10mm bolts for the motor
    • Start the second upper regulator bolt
    • Start the two lower regulator bolts
    • Tighten all the bolts
    • Tilt the window into the door
    • Lower the window by hand until it contacts the regulator
    • Insert the two 10mm bolts into the window clamps
    • Connect the window switch to its wiring harness
    • Turn on the vehicle
    • Test the window with the switch
    • Turn off the vehicle
    • Disconnect the window switch from the wiring harness
    • Put the door brace in place
    • Insert the four 10mm bolts into the door brace
  4. step : Reinstalling the Door Panel (7:00)
    • Put the water shield into place
    • Insert the two screws into the speaker
    • Put the bracket in place
    • Insert the two bolts into the bracket
    • Pull the window switch wiring harness through the door panel cavity
    • Put the door panel into place
    • Push in the door panel clips
    • Push on the mirror base panel
    • Connect the window switch wiring harness
    • Push the window switch into the door panel
    • Push the door pull cover into the door panel
    • Insert the Phillips screw into the door pull
    • Push on the door handle bezel
    • Insert the Phillips screw into the door handle

Tools needed for replacement:

    Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1998-2001Nissan Altima Nissan Altima Front Power Window Regulator with Motor Pair
Part #: 1AWRK00127


Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(09:17 min)