Replaces

1997-06 Jeep Wrangler Steering & Suspension Kit - 1ASFK05772

 

 

Our steering and suspension components come pre-greased, sealed for long life, and do not require the extra maintenance typically required by greasable versions.

Direct Fit

Application-specific, with no modifications required.

Rigorously Tested

Made from higher quality materials than the competition. Built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

By the same factories that the OEMs use.

Prepackaged for Your Convenience

Carefully assembled to include all of the parts you need, saving time and money.

Part Details

  • Kit Includes: (2) Front Outer Tie Rods
  • Kit Includes: (1) Track Bar
  • Kit Includes: (1) Steering Damper
  • Kit Includes: (2) Front Inner Tie Rods
  • Quantity: 6 Piece Set

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

  1. step : Remove the wheel (1:00)
    • Loosen the lug nuts.
    • Raise and secure the vehicle
    • Remove the lug nuts and the wheel.
  2. step : Remove the front shield (1:15)
    • Use a 15 mm socket and ratchet.
    • Remove the four bolts.
  3. step : Remove the Idler Arm (1:25)
    • Remove the 24 mm bolt securing the idler arm to the steering linkage
    • Use a joint fork and a hammer to separate the joint.
    • Remove the three other bolts securing the idler arm.
    • Use a Tie Rod Puller to pull apart the idler arm and the idler shaft.
  4. step : Install the new idler arm (4:34)
    • Assemble your new idler arm to your idler shaft, threading on the bushing and nut.
    • Bolt in the idler arm assembly into place, tightening up the three nuts.
    • Bolt in the end of the idler arm assembly to the steering gear.
    • Torque the nuts and bolts to 80 ft lbs.
    • Install the cotter pin.
    • Use a grease gun and fill the grease fitting.
  5. step : Reassembly (7:25)
    • Replace the shield with the four 15mm bolts.
    • Clip the air bag harness back in.
    • Put the wheel back on and lower the car
    • Using a star pattern torque the lug nuts to 120-140 ft lbs

Tools needed for replacement:

    General Tools

  • Hammer
  • Jack Stands
  • Large C-Clamp

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Socket Extensions
  • Torque Wrench

  • Sockets - Metric

  • 15mm Socket
  • 18mm Socket
  • 19mm Socket
  • 22mm Socket
  • 24mm Socket

  • Specialty Tools

  • Grease Gun
  • Tie Rod Fork
  • Tie Rod Puller

  • Wrenches - Metric

  • 18mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1997-2006 Jeep Wrangler Steering & Suspension Kit 6 Piece Set

This part replaces:

  • Monroe SC2942
  • KYB SS10317
  • OE # 22063969
  • OE # 52005739
  • OE # 52005740
  • OE # 52005741
  • OE # 52007118
  • OE # 52087887
  • Moog DS1235
  • Moog DS1430
  • Moog ES3094L
  • Moog ES3095R
  • Moog ES3096L
Part #: 1ASFK05772

How-to Video:

(08:13 min)