Kit Includes: (2) Tail Lights (2) Headlights with Cornering Lamps
Complete Repair in One Purchase - Stop searching for parts individually and complete your repair with a customized kit or set from DIY Solutions.
High-Quality Parts from Trusted Brands - DIY Solutions' kits and sets are selected from the best automotive brands and include hard-to-find and even obsolete parts you may need for your vehicle.
Guaranteed Fit - DIY Solutions ensures its selected parts are quality-tested to guarantee fit and function.
Assemblies may include halogen or incandescent test bulbs that should be replaced before installation.
Features and Benefits
Direct Fit - No vehicle or wiring modification necessary
DOT, SAE, and FMVSS Compliant - Meets on-road use regulations
Matching set for a restored look
Item Condition:New
Attention California Customers:
WARNING: This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov
Lifetime Warranty
This item is backed by our limited lifetime warranty. In the event that this item should fail due to manufacturing defects during intended use, we will replace the part free of charge. This warranty covers the cost of the part only.
FREE Shipping is standard on orders shipped to the lower 48 States (Contiguous United States). Standard shipping charges apply to Hawaii and Alaska.
Shipping is not available to a P.O. Box, APO/FPO/DPO addresses, US Territories, or Canada for this item.
Expedited is available on checkout to the United States, excluding Alaska, Hawaii.
Final shipping costs are available at checkout.
How to Replace Tail Lights 1997-2004 Dodge Dakota
How To Replace Headlights 1997-2004 Dodge Dakota
How To Replace Tail Lights 1997-2004 Dodge Dakota
How to Replace Headlights 1997-2004 Dodge Dakota
Created on:
Tools used
T20 Driver
1. Remove the tail light
Lower the tailgate.
Remove the two T20 Torx screws on the side of the tail light assembly.
Pull the light out, twist out the bulbs and unplug the wiring harness.
2. Install the new tail light
Transfer the wiring to the new tail light.
Twist in the bulbs.
Plug in the wiring harness and put the tail light into place.
Anchor with the two T20 Torx screws.
Close the tailgate.
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20+ years' experience restoring and repairing cars and trucks like this to show the correct way to install parts from 1AAuto.com. The right parts installed correctly. That's going to save you time and money. Thank you and enjoy the video.
The only tool you'll need is a T20 size Torx driver.
OK, so tail light replacement on a Dodge Dakota. There's two T20 torque screws right here. Once those screws are out, then you just kind of pull a little bit back on the tail light and it comes out. You're just looking to service the bulbs. You can see them right there. Now that just twists off and comes out. Maybe your tail light got wiped out by a poorly-placed 2x4 or something like that.
You can see the white - this is a new light from 1A Auto; it's just a little brighter. Everything about our light is the exact same as the original. They go in individually and slot into their posts. You can see it fits in just like the original. These guys twist in and lock, just like the original ones did. The light goes in, clips into place and then the seam screws. Then your lights in. So, you can see the new light from 1A Auto fits on just like the original and then you'll be all set to go.
Brought to you by 1AAuto.com, your source for quality replacement parts and the best service on the internet. Feel free to call us toll free, 888-844-3393, the company that's here for you on the internet and in person. Thank you.
Tools used
Gloves
Socket Extensions
T15 Torx Driver
Phillips Head Screwdriver
10mm Socket
Ratchet
Trim Tool Set
Safety Glasses
Pocket Screwdriver
Pick
Tools used
Ratchet
Trim Tool Set
T25 Torx Socket
T25 Torx Driver
Tools used
T10 Torx Driver
1. Remove the parking light
Remove the gasket from the pins securing it to the side of the headlight.
Remove the screw on the bottom corner of the headlight using your T10 Screwdriver.
Remove the parking light and unplug the bulbs.
2. Remove the headlight assembly
Remove the 3 bolts securing the headlight.
Remove the little pin securing the headlight using a cloth and screwdriver.
Unplug the harness.
To remove the bulbs just twist the locking ring and unplug the bulb.
Remove the pin that had been fastening the headlight in by pinching it and pulling it out to use later.
3. Install the new headlight assembly
Clip the pin into the new headlight that you removed in the last step.
Line up your headlight and click it into place.
Make sure your marker light is in the right spot.
Bolt everything back in.
Plug the parking light bulbs in.
Screw the parking light in with your T10 Torx driver
Pin the rubber gasket on, making sure to fold the gasket in the first time you close the hood.
Brought to you by 1AAuto.com your source for quality replacement parts and the best service on the internet.
Hi, I'm Mike Green. I'm one of the owners of 1A Auto. I want to help you save time and money repairing and maintaining your vehicle. I'm going to use my 20 plus years experience restoring and repairing cars and trucks like this to show you the correct way to install parts from 1AAuto.com. The right parts installed correctly, that's going to save you time and money. Thank you and enjoy the video.
In this video we'll be replacing a headlight on this 2000 Dodge Dakota, same as any '97 to '04 Dakota and '98 to '03 Durango. Tools you'll need are a T10 sized Torx screwdriver, a flat blade screwdriver and a 10 mm wrench or a socket and ratchet. Maybe you're replacing your headlights because they got taken out by a rock or you had a little incident or something but also you can really freshen up the front end of your truck as you can see here. Here's the truck with new headlights on it, so here's the old faded yellowed ones and then once again the new headlights. You can see that new headlights on the same truck really take a lot of miles off the front end.
Remove the parking lights first, you need to take this gasket and just remove it from these pins here. Next there's a screw at the bottom corner of the headlight and you can see it right there, this is a T10 torque screw. I'm going to remove that. That my want to just stay in there, hopefully it will ok and then once that screw is out you can actually just take parking light and pull it. These untwist and finally there's a little side mark over here that untwists and pulls out. You can replace your signal lights or you can start with the bulbs if you need to.
Now that you have the parking light off there's three bolts, I'm going to show you two of them here. That one right in there, right in the middle of the screen, that's the upper one and then there's a lower one and it's over here, right there. I'm going to remove those two and actually the third one; you can see it right behind that bulb right there. Those are 10 mm bolts you give me the ratchet and a socket. The other thing you want to do is you want to remove this bumper here and you kind of just press on the back of the bumper with your finger and pull it out. Then there's a little clip, you can just use a screwdriver and pry out.
Now we have those three bolts out but there's still a little pin holding it right here. You can unplug the back of your headlight and now your headlights free to replace. On the drivers side you can reach behind and get this but it might be actually just as easy to remove the whole headlight assembly. The passenger side your air box is in the way so if you're just looking to replace the headlight blub you will need to remove the whole light and then the headlight bulb is just like most it has a walking ring. Then the bulb comes out. The last part is when we pulled the headlight out this little part of the socket didn't come with it so its pretty easy to get in there. You're just going to have to squeeze it and pull it out with your fingers. You can see our new headlight from 1A Auto and our old headlight. Everything's the exact same just a whole lot brighter and a whole lot nicer. The new one has everything has got the tin on the back here with the clips, it has the rubber gasket and the only thing I saw is you do need to save your the little pin that goes right here. You'll just need to take this pin out of your old headlight and there's even a little indentation in it and it just goes right through on the new light.
To install our new headlight just connect the headlight bulb. If you were watching closely make sure this side marker goes up above where you bolted in and when you put it in and then line up that pin back there, push it in and actually you can take now the rubber gasket and put it in up here. Pull down through on the little tabs and then this little tin goes in. Start from the lower bolt is the easiest one. Start this bolt, black one. I've got my air ratchet and what I'm going to do is while I'm tightening this I'm going to lift up on the light to get it up right close to here, give it as nice of a position as possible.
You're going to put the parking light in so I'll just go ahead and twist. Put these ones on first. Twist and there's the little side marker again and twist. Now these kind of teeth all have slots they go in and it is possible to put them in incorrectly but basically you push it up against the light and to the side against the light and slide it in and then it's in. Now we use our T10 torque screw and put it through there. There it is and tighten it up. Put this rubber on to those two and you're all set. The first time you close the hood you want to make sure you close it slow, kind of push that gasket in and then put the hood down because the first time you close it, it may kind of flop out incorrectly.
Brought to you by www.1AAuto.com your source for quality replacement parts and the best service on the internet. Please feel free to call us toll free 888-844-3393. The company that's here for you on the internet and in person. Thank you.
LHT04321
In Stock
Product Reviews
Loading reviews
4.00/ 5.03
3 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
1
1
0
0
Parts aren't just parts
H
January 7, 2020
Received the set, looks great and thanks for video you put out it helped a lot. Thanks.
Justin
June 10, 2021
Absolutely recamend this product price was way cheaper than going to a parts store shipping was fast and ordering was easy I will be buying my parts from this site
Paul
September 22, 2021
Tail light assemblys were perfect, however drivers side headlight assembly leaked in rain water and was half filled with it because the top and sides sealant were not applied properly.
This is my second set of replacement assemblies, I hope your quality control improves. Other than that, the set was a great purchase.
Customer Q&A
No questions have been asked about this item.
Customer service
877-844-3393
Monday - Friday 8:00am - 9:30pm ET Saturday - Sunday 8:00am - 4:30pm ET
Enter Vehicle Year Make Model
Specify your vehicle's year, make and model to guarantee fit.
Year
Make
Model
Options
Drivetrain
This part doesn’t fit a . Select from parts that fit.