Replaces

1997-01 Toyota Camry Exterior Door Handle - 1ADHS01469

Description
Warranty & Shipping
How-To & Tools
Product Reviews
Q&A
Vehicle Fit

Part Details

  • Color:   Beige
  • Quantity:   4 Piece Set

These replacement door handles are just what you need to get your vehicle in good looking form again!

Specifications:

  • Comes as a SET of 4
    • Fits LH (Driver Side) and RH (Passenger Side) FRONT & REAR
  • Beige (factory color code 4M9) Painted Finish
  • Replaces dealer part number: 69210-33041-E0 ,69220-33041-E0 , 69230-AA010-E0, 69240-AA010-E0, 6921033041E0, 6922033041E0, 69230AA010E0, 69240AA010E0
  • Reinforced from the original design
  • Plastic construction

NOTE: This color is an exact match for the original factory color.  Due to things such as UV rays, weather, and age, your vehicle's paint may have faded since it was first painted.

This set makes a great replacement and provides a good value.

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to www.P65Warnings.ca.gov.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Door Panel (0:38)
    • Pry off the trim piece inside the door handle
    • Pry off the trim button on the arm rest
    • Pry off the trim button on the door panel
    • Pry up the switch panel
    • Disconnect the window switch wiring harnesses
    • Pry off the sail panel
    • Remove the three Phillips head screws on the arm rest
    • Remove the two Phillips head screws on the bottom of the door panel
    • Remove the Phillips head screw in the top left corner
    • Remove the Phillips head screw from the door handle
    • Pry off the door handle bezel
    • Pop out the bottom of the door panel
    • Pull the door panel up and off
    • Carefully remove the water shield
  2. step : Removing the Interior Door Handle (3:01)
    • Remove the Phillips head screw from the door handle
    • Pull off the metal latch rods from the door handle
    • Remove the metal plate
    • Carefully pry off the weather shield
  3. step : Removing the Exterior Door Handle (4:24)
    • Connect the window switch
    • Turn the key to the run position
    • Raise the window
    • Disconnect the door handle latch rod
    • Pry the door latch rod from the door handle
    • Remove the safety latch from the lock rod
    • Push the lock rod out of the door handle
    • Remove the two 10mm bolts from the door handle
    • Lift the door hand up and out
    • Remove the 10mm screw from the lock cylinder
    • Remove the lock cylinder from the door handle
  4. step : Installing the Exterior Door Handle (6:37)
    • Insert the lock cylinder into the new door handle
    • Insert the door handle into the door
    • Tighten the 10mm screws to the door handle
    • Insert the lock rod into the lock cylinder
    • Close the clip on the lock rod
    • Insert the door handle rod into the door handle
    • Close the latch onto the rod
    • Press the watershield to the inside of the door
  5. step : Installing the Interior Door Handle (8:23)
    • Insert the metal shield into place
    • Tighten the three Phillips screws to the shield
    • Insert the lock rod into the door handle
    • Insert the hooks into the door and slide the handle back
    • Tighten the Phillips screw to the door handle
  6. step : Reinstalling the Door Panel (9:42)
    • Lift the door panel into place
    • Push in the door panel clips
    • Tighten the two Phillips head screws at the bottom
    • Tighten the three Phillips head screws to the arm rest
    • Tighten the Phillips head screw to the top left of the door panel
    • Connect the window switch wiring harness
    • Press the window switch into place
    • Insert the door handle trim bezel into place
    • Tighten the Phillips screw to the door handle trim
    • Press the trim bezel inside the door handle in

Tools needed for replacement:

    General Tools

  • Pick

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

5.00/ 5.0
1review
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
1
0
0
0
0
Door Handles
The door Handles were exactly what I expected them to be !!!! Thank you!!!!
April 9, 2017
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
are they same quaty as oem parts door handles?
Jerry M July 27, 2017
made with different parts, quality is good
Godfrey H July 27, 2017
Nothing ever is but they are good enough to last
Wayne R July 27, 2017
They are an aftermarket design, but built to meet or exceed the OE specifications.
Alex P July 28, 2017
Fit right on and matched original paint. Very satisfied. Would order again if something else needed.
Brenda D July 28, 2017
I am not sure it equal to OEM quality but it is working good for the price.
Timothy S July 29, 2017
Year Make Model Description
1997-2001Toyota Camry Toyota Camry Front & Rear Beige Exterior Door Handle 4 Piece Set
Part #: 1ADHS01469

Out of Stock

How-to Video:

(12:18 min)