Replaces

1997-01 Honda CR-V Steering & Suspension Kit - 1ASFK02581

Specifications:

  • Brand New Steering & Suspension Kit
  • Comes as a 12 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacements
  • Built to strict quality control standards

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheels (1:00)
    • Loosen the lug nuts
    • Raise and secure the vehicle
    • Remove the wheel
  2. step : Remove the tie rod (1:32)
    • Mark the alignment on the tie rod with a sharpie.
    • Use two wrenches to loosen up the tie rod nut.
    • Remove the cotter pin and remove the 16 mm nut.
    • Use a tie rod puller to pry out the tie rod.
    • Unscrew the tie rod.
  3. step : Install the new tie rod (4:05)
    • Adjust the new locking nut to the same spot that the old one was (where you made your mark)
    • Screw in the new tie rod.
    • Install the cotter pin and bolt on the 17mm nut.
    • Install the cotterpin.
    • Use a grease gun to fill the joint.
  4. step : Replace the wheel (7:15)
    • Put the wheel on and hand tighten the lug nuts
    • Lower the car and torque the lug nuts to 80 ft lbs.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench
  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 16mm Socket
  • 17mm Socket
  • 18mm Socket
  • 19mm Socket

  • Specialty Tools

  • Grease Gun
  • Tie Rod Puller

3.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
0
0
1
0
0
not satisfied,
Parts were not exact fits. Most of the parts were very cheaply made.
June 26, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1997-2001 Honda CR-V 12 Piece Set Steering & Suspension Kit

This part replaces:

  • Reference Number ES2943R, ES3331R
  • Dorman 520-647
  • Dorman 520-648
  • Hollander 511-58133L
  • Hollander 511-58133R
  • OE # 53534-SR3-N52, 53534-ST0-013
  • OE # 53560S04013, 53560S04013
  • OE # 53540S04013, 53540S04003
  • OE # 53010S10003, 53010S1000
  • OE # 53534S30003, 53534SV4003
  • OE # 51460-S10-020
  • OE # 51450-S10-020
  • OE # 51320S04003
  • Moog K9863
  • Moog K9802
  • Moog ES3332R
  • Moog ES3331R
  • Moog K90667
  • Moog EV414
  • Moog K80884
  • Moog K80883
  • Beck Arnley 103-2865
  • Beck Arnley 101-4698
Part #: 1ASFK02581


How-to Video:

(08:20 min)