Replaces

1996 Fuel Pump & Sending Unit Module TRQ FPA86492 - 1AFPU01370

This assembly features the following specifications:

  • Mounts in fuel tank
  • Complete assembly
  • Replaces dealer part numbers: 19179984
  • Outlets: 3
  • Assembly includes the following parts:
    • Electric Fuel Pump
    • Fuel sending unit
    • Rheostat Range: 0-90 Ohms
    • Float
    • Strainer
  • Direct replacement
  • Connector style:
    • (1) White Oval 4 Prong Connector
    • (1) Black Oval 3 Prong Connector

 

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

 

This fuel pump includes a new electrical connector harness. You will need to remove your existing electrical connector and install the new connector provided in order to install your new fuel pump (instructions are included with the pump).

This fuel pump is not a universal fit item. Because your vehicle’s original connector is prone to failure due to corrosion, cracking, loose pin housings, and wire crimp issues, the OE manufacturer has changed the shape of the connector, requiring the install of a new electrical connector during fuel pump service.

Part Details

  • Includes: (1) Wire Stripper / Crimper Tool

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Disconnecting the Fuel Pump Relay (0:45)
    • Turn the vehicle on and run the engine
    • Open the fuse box door
    • Locate and remove the fuel pump relay with pliers
    • Insert the fuel pump relay into the fuse box
    • Close the fuse box door
  2. step : Removing the Fuel Pump Panel (1:05)
    • Pull the back seats down
    • Pull the trim and carpet apart
    • Remove the 10mm bolts from the fuel pump panel
    • Pry up on the panel with a flat blade screwdriver
  3. step : Removing the Fuel Pump (2:07)
    • Pull up on the pin from the sending unit
    • Disconnect the sending unit wiring harnesses
    • Push the outside fuel lines in, push down on the tab, and pull them free
    • Push the tab on the center fuel line and pull it free
    • Hammer the locking ring with a flat blade screwdriver to turn the locking ring
    • Lift the locking ring up and off
    • Pull the fuel pump up
    • Let the pump drain
    • Lift the fuel pump up and out
  4. step : Preparing the Fuel Pump (3:55)
    • Apply the level sensor to the new fuel pump
    • Remove the fuel line clips from the old sensing unit
    • Remove the packing cap from the new fuel pump
    • Insert the fuel line clips onto the new fuel pump
    • Cut off the old sending unit wiring harness with the blue strip with wire cutters
    • Strip a quarter of an inch off the old wires with wire cutters
    • Apply the blue connectors on the grey and black wire
    • Apply the red connectors to the purple and black and white wire
    • Connect the new sending unit harness to the connectors
  5. step : Installing the Fuel Pump (7:39)
    • Place the fuel pump and sending unit into the fuel tank
    • Fit the locking ring into place and line up the slots with the tabs without pinching the harnesses
    • Twist the ring clockwise with a flat blade screwdriver and hammer
    • Remove one of the posts from the locking ring with a pair of pliers
    • Connect the pin to the sending unit
    • Connect the wiring harnesses to the fuel pump
    • Connect the fuel lines
  6. step : Reinstalling the Fuel Pump Panel (10:20)
    • Replace the panel
    • Insert and tighten the 10mm bolts
    • Cover the panel with the trim and carpet
    • Pull the back seats up

Tools needed for replacement:

    General Tools

  • Hammer

  • Pliers, Cutters & misc Wrenches

  • Wire Cutters
  • Wire End Cutters
  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1996 Chevy S10 Pickup L4 2.2L Fuel Pump & Sending Unit Module with (1) Wire Stripper / Crimper Tool TRQ
  • 1996 GMC S-15 Sonoma L4 2.2L Fuel Pump & Sending Unit Module with (1) Wire Stripper / Crimper Tool TRQ
  • 1996 Isuzu Hombre Fuel Pump & Sending Unit Module with (1) Wire Stripper / Crimper Tool TRQ

This part replaces:

  • Hollander 323-01034
  • Airtex E3923M
  • Spectra Premium Industries TNKSP359M
  • OE # 19179984
  • TRQ FPA86492
Part #: 1AFPU01370

Out of Stock

TRQ
Brand #: FPA86492

How-to Video:

(11:21 min)