1996-02 Toyota 4Runner Heater Blower Motor with Fan Cage - 1AHCX00175

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

This Toyota 4Runner FRONT heater blower motor with fan cage is a new, aftermarket replacement part. It is just what you need to bring your heating and A/C blower system back to good working order! This assembly has the following


  • New, not remanufactured or rebuilt
  • Includes blower motor fan cage impeller already installed
  • Direct replacement
  • Replaces dealer part numbers: 8710335020, 8710335021, 8710335022, 87103-35020, 87103-35021, 87103-35022
  • Built to strict quality control standards
  • 100% tested prior to leaving the factory
  • Fits the FRONT blower motor

If you are experiencing intermittent stopping during use, squealing noise from bearings, or poor air flow from your dash vents this may be your solution.

Our electrical and electronic parts are subject to strict quality control testing. Please ensure proper diagnosis of this item before purchasing as the item cannot be returned once installed or plugged in.

Left Hand Drive Note:

“All of our auto parts are intended for Left Hand Drive USDM vehicles and might not have been tested on Right Hand Drive platforms. If your vehicle is Right Hand Drive, please do your research prior to making a purchase to ensure the part is correct for your specific vehicle.”

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Accessing the Blower Motor (0:37)
    • Remove the four Phillips head screws from the door sill plate
    • Remove the sill plate
    • Pry off the kick plate by hand
  2. step : Removing the Blower Motor (1:19)
    • Disconnect the wiring harness from the blower
    • Remove the three screws from the blower with either a T25 Torx Driver or an 8mm socket
    • Pull out the blower
  3. step : Installing the New Blower Motor (2:22)
    • Put the new blower into place with the tab on the left
    • Start the three screws by hand
    • Tighten the three screws
    • Attach the blower motor wiring harness
    • Turn the car on
    • Test the fan
    • Turn the car off
  4. step : Reinstalling the Trim Panels (3:41)
    • Snap the kick panel into place
    • Put the sill plate in place
    • Insert the four Phillips screws into the sill plate

Tools needed for replacement:

    Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 8mm Socket

  • Torx Drivers & Sockets

  • T25 Torx Driver

4.50/ 5.0
2 reviews
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Heater Blower Motor with Fan Cage
Part was extremely affordable and easy to install. Part overall operates identically to original part. Does have a slight whistle when operating at highest speed, but again overall extremely satisfied to have my fan blower working in order to have A/C during these 110+ summer temps ??
June 21, 2017
Toyota 4Runner A/C blower fan
Ordered this to replace a malfunctioning unit. Fits perfectly and returned the a/c to full functionality. Great customer service.
October 1, 2017
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1996-2002Toyota 4Runner Toyota 4Runner Front Heater Blower Motor with Fan Cage
Part #: 1AHCX00175

Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(04:41 min)