Specifications:

  • Semi Metallic Disc Brake Pads
  • 4 Piece rear brake pad set
  • Includes shims
  • Direct replacements
  • Fits models with 1" Wide Clip only (Phenolic Piston Calipers)
    • Does NOT fit models with 1-3/4" Wide Clip (Steel Piston Calipers)

 

Positive Mold Technology

Positive Mold Technology improves durability and performance by allowing for even wear. High density, low resin friction material virtually eliminates brake fade and glazing, generates less brake dust, and promotes a longer-lasting , better performing brake pad.

OE Grade Multi-Layer Shim

OE Grade Multi-Layer Shim helps reduce vibration and noise

Environmentally Compliant

Certified Environmentally Compliant to "Better Brake Law" standards

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

Wear and Tear

This item is backed by a warranty against defects in materials and workmanship under its intended use. The warranty does not cover normal wear and tear. Please keep your invoice for proof of this warranty.

  1. step : Removing the Wheel (0:50)
    • Pry off the center cap with a flat blade screwdriver
    • Retrieve the center nut key from the glove box
    • Use the key to loosen the center nut
    • Pull off the wheel cover
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel cover bracket
    • Pull off the wheel
  2. step : Inspecting the Brakes (1:21)
    • Check the thickness of the brake pads
    • Check for gouges on both sides of the rotor
  3. step : Removing the Brake Pads (1:50)
    • Remove the two 10mm bolts from the brake caliper
    • Pry off the caliper with a flat blade screwdriver
    • Pull the caliper aside
    • Pull the inner brake pad out of the caliper
    • Pry the outer brake pad off with a flat blade screwdriver
  4. step : Removing the Brake Rotor (2:49)
    • Apply penetrating oil to the wheel studs
    • Pull the rotor off
    • If the rotor will not come off, strike rotor with a hammer to loosen it
  5. step : Installing the New Brake Rotor (3:24)
    • Slide the rotor on
    • Thread on one lug nut to hold the rotor in place
  6. step : Installing the New Brake Pads (3:41)
    • Put an old pad in the caliper
    • Use a large C-clamp and the old pad to push the pistons back
    • Install the new brake pads into the caliper
    • Clean the brake pad slides with a wire brush
    • Check that the caliper slides move freely
    • Apply grease to the caliper slides, if necessary
    • Put the caliper on
    • Thread the two 10mm bolts by hand
    • Tighten bolts to between 12 - 15 foot-pounds
  7. step : Reattaching the Wheel (6:50)
    • Remove the placeholder lug nut
    • Slide the wheel into place
    • Put the wheel cover bracket into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 100 - 120 foot-pounds in a crossing or star pattern
    • Put the wheel cover into place
    • Tighten the center nut with the key
    • Reattach the center cap
    • Return the center nut key to the glove box
  8. step : Testing the Brakes (7:39)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Large Hammer
  • Wire Brush
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Bearing Grease
  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Torque Wrench
  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 21mm Socket

  • Wrenches - Metric

  • 12mm Wrench
  • 11mm Wrench
  • 10mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1996-2002 Ford Crown Victoria Rear Semi-Metallic Brake Pads for Models with Rear Phenolic Piston Calipers with 1 Inch Pad Clip
  • 1996-2002 Lincoln Town Car Rear Semi-Metallic Brake Pads for Models with Rear Phenolic Piston Calipers with 1 Inch Pad Clip
  • 1996-2002 Mercury Grand Marquis Rear Semi-Metallic Brake Pads for Models with Rear Phenolic Piston Calipers with 1 Inch Pad Clip

This part replaces:

  • Reference Number MD674A
Part #: 1ABPS00372

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(08:16 min)