Replaces

1996-00 Honda Civic Door Lock Actuator Pair - 1ADRK00111

These are the power door lock actuators that mounts inside the doors. They are designed to REPLACE a broken or missing unit.

Specifications:

  • Comes as a PAIR
    • Fits LH (Driver Side) and RH (Passenger Side)
  • Replaces dealer part numbers: 72115-S00-A01, 72115-S04-A02, 72115-S04-J02, 72115S00A01, 72155-S00-A01, 72115S04A02, 72115S04J02, 72155S00A01
  • Correct electrical connection
  • Direct replacement
  • Built to strict quality control standards
  • Fits 2 Door Coupe Models only

This power door lock actuator pair is built to strict quality control standards. It is a great replacement and has good cost savings over a dealer pair.

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the door panel (1:12)
    • Remove the two Phillips screws from the door pull
    • Use a flat blade screwdriver to pry out the door handle bezel.
    • Use a putty knife to carefully pry off the door panel and unclip the clips securing it.
    • Pull off the panel and unplug all the wiring
  2. step : Remove the door lock actuator (3:45)
    • Carefully pull aside the plastic water shield
    • Drill out the rivets securing the door lock actuator.
    • Unclip the lock rods and unplug the wiring harness
    • Transfer the mounting bracket and dust cover to the new lock actuator
  3. step : Install the new door lock actuator (5:40)
    • Use a couple coarse threaded bolts rather than rivets to re-install the door lock actuator
    • Plug in the wiring harness and lock rods.
    • Test your connections to make sure the doors lock and unlock properly.
  4. step : Re-install the door panel (7:00)
    • Put the water shield back into place.
    • Reconnect the speaker and light.
    • Thread the wiring harness back into place.
    • Clip the door panel back on.
    • Re-install the door handle bezel.
    • Plug in the control panel.
    • Bolt back in the door handle pull using your Phillips screwdriver.

Tools needed for replacement:

    Drills, Drill Bits & Related

  • 5/16 Inch Drill Bit

  • General Tools

  • Putty Knife

  • Materials, Fluids, and Supplies

  • Cloth Rags

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 4mm Socket

  • Specialty Tools

  • Door Panel Removal Tool

5.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
1
0
0
0
0
Works great
Great price, great fit, easy install, works great. Will shop here again!
June 20, 2017
Purchased
1 year ago
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1996-2000 Honda Civic 2 Door Coupe Door Lock Actuator Pair
Part #: 1ADRK00111

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(10:01 min)