These replacement suspension parts are just what you need to ensure the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Suspension/Steering Kit includes:
    • (2) - FRONT UPPER Ball Joints - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT LOWER Ball Joints - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT INNER Tie Rod Ends - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT OUTER Tie Rod Ends - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT Tie Rod Adjusting Sleeves - LH (Driver Side) & RH (Passenger Side)
    • (2) - FRONT Sway Bar End Links - LH (Driver Side) & RH (Passenger Side)
    • (2) - REAR Sway Bar End Links - LH (Driver Side) & RH (Passenger Side)
    • (1) - Steering Pitman Arm
    • (1) - Steering Idler Arm
  • Direct replacements
  • Built to strict quality control standards

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel (1:16)
    • Loosen the lug nuts with a lug wrench or 19 mm socket and ratchet.
    • Raise and secure the vehicle.
    • Remove the lug nuts and wheel.
  2. step : Remove the cams (1:33)
    • Secure the frame of the vehicle.
    • Jack up the control arm/suspension of the car.
    • Mark your inner and outer cams to help align your vehicle during assembly.
    • Remove the 22 mm bolts and remove the inner and outer cams.
  3. step : Remove the upper ball joint (3:35)
    • Remove the 18 mm nut and remove bolt.
    • Remove the upper ball joint.
  4. step : Install the new upper ball joint. (4:10)
    • Fit the ball joint into the steering knuckle and over the control arm studs.
    • Work the upper ball joint into place.
    • Bolt down with the 18 mm ball joint locking nut.
    • Put your cams down on the control arm studs and thread on the locking nuts.
    • Line up your marks on the cams and tighten down the lock nuts the rest of the way.
    • Tighten up the pinch bolt to 90 ft lbs.
    • Torque the control arm nuts to 118 ft lbs.
    • Insert your grease fitting and fill with the grease gun.
  5. step : put your wheel back on (7:51)
    • Hand tighten your lug nuts
    • Lower the suspension and the vehicle.
    • Torque your lug nuts in a star pattern to 100-110 ft lbs.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench
  • Adjustable Wrench

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 22mm Socket
  • 18mm Socket
  • 21mm Socket
  • 19mm Socket
  • 20mm Socket

  • Specialty Tools

  • Grease Gun

4.0 / 5.0
1 Review
5 Stars
4 Stars
3 Stars
2 Stars
1 Stars
0
1
0
0
0
Everything needed.
All the parts that were in this kit fit well. The car handles great after getting the front alignment done.
April 4, 2016
Purchased
over 2 years ago
Start typing your question and we'll check if it was already asked and answered. Learn More
Browse 1 question Browse 1 question and 1 answer
#1ASFK00463 Will this part fit my 1994 crown victoria?
Nicholas M on Dec 28, 2016
BEST ANSWER: This kit is specific to year model 1995 to 1997 Crown Victorias. At this time we do not have a similar kit available for your 1994 model.

How-to Video:

(08:44 min)

Tools List:

    General Tools

  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench
  • Adjustable Wrench

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 22mm Socket
  • 18mm Socket
  • 21mm Socket
  • 19mm Socket
  • 20mm Socket

  • Specialty Tools

  • Grease Gun



This part replaces:

  • Moog K8678
  • Moog ES3311S
  • Moog K8848
  • Moog K8685
  • Moog K8283
  • Moog K8688
  • Moog ES2057RL
  • Moog ES3494
  • Moog K8853
  • OE # 2W7Z3A130A, F5AZ3A130A
  • OE # F3AZ3A131A, 2W7Z3A131AA
  • OE # F8AZ3590AA
  • OE # F6AZ 5K484 AA

Vehicle Fit

  • 1995-1997 Ford Crown Victoria Suspension Kit
  • 1995-1997 Lincoln Town Car Suspension Kit
  • 1995-1997 Mercury Grand Marquis Suspension Kit
Part #: 1ASFK00463

Ships Same Day for orders placed by 4 P.M. ET

We're here to help

1A Auto Parts

Customer Feedback

"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More