The ignition coil is a crucial part of your ignition system. It's function is to convert the 12 volt power of your vehicle's electrical system in to 35,000 or more volts. This produces a high intensity spark at the spark plug which then ignites the fuel in the cylinder. Coils in general will wear out over time and cause a misfire condition. In engines like this that use a coil, if the coil goes bad, the complete assembly needs to be replaced.

This Ignition Coil features the following specifications:

  • New not remanufactured
  • Replaces dealer part numbers: 30520-P0G-A02, 30520P0GA02, 4598371
  • Built to strict quality control standards
  • Direct replacement
  • 100% factory tested
  • Fits the following Honda 6 cylinder engines as listed:
    • V6 2.7L

 

Our electrical and electronic parts are subject to strict quality control testing.  Once the item has been installed or plugged in, it is no longer eligible for a refund.  The item may be eligible for replacement, only if it is found to have a manufacturing defect. Before purchasing, please ensure proper diagnosis of the failed original part is performed

Direct Fit Replacement

Direct fit replacement part is guaranteed to fit and function properly for your specific application.

Optimum Performance

Optimal performance, TRQ ignition coils are designed to meet or exceed the requirements of the vehicle.  TRQ ignition coils provide the correct primary and secondary resistance, voltage output, and spark energy that the vehicle needs to restore to its original operating condition.

Premium Quality

Manufactured with quality components and materials by using advanced technology to meet the highest quality control standards in the industry.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Removing the Distributor (1:02)
    • Unplug the wire underneath the distributor from the coil and distributor.
    • Remove the two 8mm bolts.
    • Pull the cap away.
    • You want the rotor to be facing straight up. Turn the key in the ignition to spin it into place.
    • Remove the 12mm bolt to the side of the distributor.
    • Pull the distributor out and press the button on the connector to remove it.
  2. step : Replacing the Ignition Coil (4:16)
    • Disconnect the ignition coil harness.
    • Remove the three 10mm bolts.
    • Pull the ignition coil out.
    • Put a bolt through the new ignition coil and put it down into place.
    • Replace and tighten all three 10mm bolts.
    • Plug the harness back in.
  3. step : Replacing the Distributor (7:05)
    • Reconnect the distributor.
    • Put the distributor into place exactly the way it was.
    • Replace the 12mm bolt.
    • Replace the distributor cap.
    • Replace the 8mm bolts.
    • Replace the wire.

Tools needed for replacement:

    Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Sockets - Metric

  • 10mm Socket

  • Wrenches - Metric

  • 12mm Wrench
  • 8mm Wrench

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1995-1997 Honda Accord Ignition Coil V6 2.7L (6th Vin Digit 6)

This part replaces:

  • OE # 30520P0GA02
  • Hollander 610-58436
  • Standard Motor Products UF-200
Part #: 1AECI00160

Ships Same Day for orders placed by 4 P.M. ET

How-to Video:

(09:19 min)