1995-97 Dodge Intrepid Lighting Kit - 1ALHP00001

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Quantity:   4 Piece Set
  • Kit Includes:
      (2) Headlights
      (2) Headlight Mounting Brackets


  • Brand New Lighting Kit
  • Comes as a 4 Piece Kit
    • Fits LH (Driver Side) & RH (Passenger Side)
  • Direct replacement
  • Built to strict quality control standards
Fit guaranteed
  • This pair of headlamps will install just as your originals do. You can use your existing hardware and wiring harnesses.
  • Save time and money with a direct fit. No trips to the hardware store or extra time trying to get the wiring to hookup.
  • 1A Auto has the most comprehensive warranty.
  • If this headlight set should fail to provide satisfactory performance you may exchange it.
  • 1A Auto Headlights are guaranteed to pass inspections in all 50 states. DOT (U.S. Dept. of Transportation) and SAE (Society of Automotive Engineers) approved.
  • Replacing discolored, scratched, dull or damaged headlights with a new pair from 1A Auto can increase your resale value by up to 10%.
  • A new pair of headlights can provide you with up to 50% more illumination than a dull, yellowed, sandblasted, broken or scratched headlight.
    • 1A Auto headlights can help you see farther at night and in poor driving conditions.
    • A new pair of headlights from 1A Auto can make you more visible to other traffic during heavy rain or wintry weather.
Direct Fit Replacement

Direct fit replacement for OEM assembly

Trouble-free Installation

Uses same wiring as original assembly.  No cutting or splicing required.

DOT and SAE Compliant

Meets federal regulations for on-road use

Item Condition: New

Attention California Customers:

WARNING:  This product can expose you to chemicals including Chromium (Hexavalent Compounds), which is known to the State of California to cause cancer, and birth defects or other reproductive harm.  For more information, go to

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

Bulb Note:

These lights do not include bulbs.  If you happen to receive a product with bulbs, the bulbs are for testing and not covered under our warranty.  Our warranty applies to the light assembly only.

  1. step : Removing the Bumper Cover (0:58)
    • Remove the six Phillips screws in the front of the wheel well.
    • Pull the inner fender panel down.
    • Remove the 3/8â€� bolt from behind the inner fender panel.
    • Do the same process in the opposite wheel well.
    • Remove the five 3/8 bulbs from the bottom of the bumper cover.
    • Pull the bumper cover out on either side and off.
    • Disconnect the fog lights and put the bumper cover aside.
  2. step : Removing the Headlight Bracket (3:18)
    • Push the tab on the back of the parking light and pull the light free.
    • If keeping the headlight remove it by removing the two screws on the sides and loosening the center screw.
    • Remove the four 10mm bolts securing the bracket to the car.
    • Pull the bracket free.
  3. step : Replacing the Headlight Bracket (4:30)
    • Remove the clip from the new one and replace it with the old clip.
    • Put the bracket into place making sure the wire harness goes up through the hole on the back.
    • Replace those four 10mm bolts.
    • Reconnect the headlight and replace the light.
    • Replace the three screws.
  4. step : Adjusting the Headlight (5:50)
    • Using the two screws at the top of the headlight aim the lights.
    • The screw on the inside controls left and right. The one on the outside angles it up and down.
    • Aim the light at a wall 20 feet away.
    • The concentration of the low beam on the wall should be 1â€� below the bulb. And straight ahead.
    • The high beam concentration should line up with the low beam bulb.
  5. step : Replacing the Bumper Cover (6:12)
    • Reinstall the parking light.
    • Reconnect the fog lights.
    • Place the bumper into place and connect the clips on either side.
    • Replace the bolt inside the inner fender.
    • Replace the six bolts that secure the inner fender.
    • Repeat this on both sides. Use an awl to help line up the fender by pushing it through the screw holes.
    • Replace the five 3/8â€� bolts under the bumper cover.

Tools needed for replacement:

    Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Sockets - SAE

  • 3/8 Inch Socket

  • Torx Drivers & Sockets

  • T15 Torx Driver

There are no reviews for this item.
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1995-1997Dodge Intrepid Dodge Intrepid 4 Piece Set Lighting Kit
Only 3 left in stock
Part #: 1ALHP00001

Order must be placed by 4pm ET

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(10:03 min)