1995-05 CV Axle Shaft TRQ CSA82203 - 1AACV00149

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit


  • Fits either LH (Driver Side) or RH (Passenger Side) Front
  • CV Style Axle Shaft
  • Brand New, not refurbished or rebuilt
  • Built to strict quality control standards
  • No core charge
  • Correct for models with or without ABS (Anti-Lock Brakes)

CV axles are designed to transmit the power from your vehicle's drivetrain to the wheels while being able to flex and pivot to the demands of the steering and suspension systems.  If your vehicle is making clicking noises at lower speeds or when making turns, it may be time to replace your CV axles with our 100% brand new assemblies.

Note: This is correct for models with or without ABS brakes.  The tone ring can be removed if the original CV axle did not have one and the vehicle did not originally come equipped with ABS brakes.

Note: You may need to reuse your original inner stub shaft with this new replacement CV axle.  The splined shaft on the inner joint from your original assembly can be removed and installed onto the new CV assembly.

100% New Components

For quality fit, finish, and easy installation.

Heat Treated

For longer-lasting life and consistent performance under different road conditions.

Precision Machined

And made of brand new components, held to tighter tolerances for better consistency than rebuilt parts.

Item Condition: New

Attention California Customers:

WARNING: Cancer and Reproductive Harm -

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:49)
    • Loosen the lug nut caps with a 19mm socket
    • Pull off the hub cap
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Axle (1:15)
    • Apply penetrating oil to the axle nut
    • Remove the hub nut with a 30mm socket and breaker bar
    • Remove the hub nut washer
    • Apply penetrating oil to the axle splines
    • Push the axle out of the hub with a hammer and a block of wood
    • Turn the spindle assembly by hand
    • Apply penetrating oil to the strut assembly nuts
    • Loosen the 21mm nuts from the strut assembly with a breaker bar and pipe for leverage
    • Remove the 21mm nuts with a ratchet
    • Tap the bolts out of the strut assembly with a hammer
    • Pull apart the lower nut and spindle with a pry bar
    • Apply penetrating oil to the brake line bracket bolt
    • Remove the 13mm bolt from the brake line bracket
    • Pull the spindle back and pull the axle out of the hub
    • Pry the axle away from the output housing with a pry bar
    • Pull the axle out by hand
  3. step : Installing the New Axle (4:38)
    • Push the transmission end of the axle in, making sure the clip locks in
    • Push the axle all the way in, and push the hub end into the hub
    • Install the hub nut and washer
    • Preliminarily tighten the hub nut
    • Insert the 13mm bolt into the brake line bracket
    • Line up the spindle with the strut assembly
    • Insert the bolts into the strut assembly
    • Tap the bolts in with a hammer
    • Put the 21mm nuts on to the strut bolts
    • Tighten the 21mm nuts to 100 foot-pounds of torque
  4. step : Reattaching the Wheel (7:32)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut to between 145-150 foot-pounds
    • Tighten the lug nuts to 90 foot-pounds in a crossing or star pattern
    • Put the hub cap on, lining up the notch with the valve stem
    • Tighten the lug nut covers with a 19mm socket

Tools needed for replacement:

    General Tools

  • Hammer
  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Rust Penetrant
  • Block of Wood

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Torque Wrench
  • 1/2 Inch Breaker Bar
  • Ratchet

  • Screwdrivers & Related

  • Pry Bar

  • Sockets - Metric

  • 30mm Socket
  • 13mm Socket
  • 21mm Socket
  • 19mm Socket

5.00/ 5.0
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
As Ive come to expect
Quality part, arrived on schedule, installed easily.
November 2, 2017
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1995-2005Chevy Cavalier Chevy Cavalier Front CV Axle Shaft for Models with 4 Speed Automatic Transmission Driver or Passenger Side TRQ CSA82203
1995-2005Pontiac Sunfire Pontiac Sunfire Front CV Axle Shaft for Models with 4 Speed Automatic Transmission Driver or Passenger Side TRQ CSA82203
Part #: 1AACV00149

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Brand #: CSA82203

How-to Video:

(08:41 min)