Specifications:

  • Brand New Suspension Kit
  • Fits LH (Driver Side) & RH (Passenger Side) Front
  • Built to strict quality control standards
  • Direct replacement

Our steering and suspension components are sealed for long life and do not require the extra maintenance typically required by greasable versions.

Please Note: Whenever replacing steering components, it is highly recommended to have a professional alignment performed on the vehicle afterwards.  Failure to do so may result in issues with steering and premature tire wear.

Direct Fit

All parts are direct fit, application-specific parts with no modifications required

Rigorously Tested

Rigorously tested and made from higher quality materials than the competition. Our parts are built to have a longer life in any environment or road conditions.

State of the Art Manufacturing

Our parts are manufactured by some of the same factories that the OEMs use.

Prepackaged for Your Convenience

Our kits have been carefully put together to include all of the parts you need to get the job done, saving you both time and money. These kits also help take the guesswork out of finding the correct part for your vehicle’s steering or suspension system, allowing you to get started on your repair project faster.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. step : Remove the wheel (1:16)
    • Loosen the lug nuts with a lug wrench or 19 mm socket and ratchet.
    • Raise and secure the vehicle.
    • Remove the lug nuts and wheel.
  2. step : Remove the cams (1:33)
    • Secure the frame of the vehicle.
    • Jack up the control arm/suspension of the car.
    • Mark your inner and outer cams to help align your vehicle during assembly.
    • Remove the 22 mm bolts and remove the inner and outer cams.
  3. step : Remove the upper ball joint (3:35)
    • Remove the 18 mm nut and remove bolt.
    • Remove the upper ball joint.
  4. step : Install the new upper ball joint. (4:10)
    • Fit the ball joint into the steering knuckle and over the control arm studs.
    • Work the upper ball joint into place.
    • Bolt down with the 18 mm ball joint locking nut.
    • Put your cams down on the control arm studs and thread on the locking nuts.
    • Line up your marks on the cams and tighten down the lock nuts the rest of the way.
    • Tighten up the pinch bolt to 90 ft lbs.
    • Torque the control arm nuts to 118 ft lbs.
    • Insert your grease fitting and fill with the grease gun.
  5. step : put your wheel back on (7:51)
    • Hand tighten your lug nuts
    • Lower the suspension and the vehicle.
    • Torque your lug nuts in a star pattern to 100-110 ft lbs.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • Marker / Writing Utensil

  • Pliers, Cutters & misc Wrenches

  • Lug Wrench
  • Adjustable Wrench

  • Ratchets & Related

  • 1/2 Inch Breaker Bar
  • Ratchet
  • Torque Wrench
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 22mm Socket
  • 18mm Socket
  • 21mm Socket
  • 19mm Socket
  • 20mm Socket

  • Specialty Tools

  • Grease Gun

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

Vehicle Fit

  • 1995-2002 Ford Crown Victoria Front Suspension Kit 8 Piece Set
  • 1995-2002 Lincoln Town Car Front Suspension Kit 8 Piece Set
  • 1995-2002 Mercury Grand Marquis Front Suspension Kit 8 Piece Set

This part replaces:

  • OE # 2W7Z3A130A, F5AZ3A130A
  • OE # F3AZ3A131A, 2W7Z3A131AA
  • Moog K8678
  • Moog K8685
  • Moog ES2057RL
  • Moog ES3494
Part #: 1ASFK02253


How-to Video:

(08:44 min)