1993-97 Dodge Intrepid Headlight Mounting Bracket Pair - 1ALHP00475

Frequently bought together

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit

Part Details

  • Quantity:   Pair


  • Comes as a pair
  • Includes leveling bubble
Fit guaranteed
  • This pair of headlamps will install just as your originals do. You can use your existing hardware and wiring harnesses.
  • Save time and money with a direct fit. No trips to the hardware store or extra time trying to get the wiring to hookup.
  • 1A Auto has the most comprehensive warranty.
  • If this headlight set should fail to provide satisfactory performance you may exchange it.
  • 1A Auto Headlights are guaranteed to pass inspections in all 50 states. DOT (U.S. Dept. of Transportation) and SAE (Society of Automotive Engineers) approved.
  • Replacing discolored, scratched, dull or damaged headlights with a new pair from 1A Auto can increase your resale value by up to 10%.
  • A new pair of headlights can provide you with up to 50% more illumination than a dull, yellowed, sandblasted, broken or scratched headlight.
    • 1A Auto headlights can help you see farther at night and in poor driving conditions.
    • A new pair of headlights from 1A Auto can make you more visible to other traffic during heavy rain or wintry weather.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Bumper Cover (0:58)
    • Remove the six Phillips screws in the front of the wheel well.
    • Pull the inner fender panel down.
    • Remove the 3/8â€� bolt from behind the inner fender panel.
    • Do the same process in the opposite wheel well.
    • Remove the five 3/8 bulbs from the bottom of the bumper cover.
    • Pull the bumper cover out on either side and off.
    • Disconnect the fog lights and put the bumper cover aside.
  2. step : Removing the Headlight Bracket (3:18)
    • Push the tab on the back of the parking light and pull the light free.
    • If keeping the headlight remove it by removing the two screws on the sides and loosening the center screw.
    • Remove the four 10mm bolts securing the bracket to the car.
    • Pull the bracket free.
  3. step : Replacing the Headlight Bracket (4:30)
    • Remove the clip from the new one and replace it with the old clip.
    • Put the bracket into place making sure the wire harness goes up through the hole on the back.
    • Replace those four 10mm bolts.
    • Reconnect the headlight and replace the light.
    • Replace the three screws.
  4. step : Adjusting the Headlight (5:50)
    • Using the two screws at the top of the headlight aim the lights.
    • The screw on the inside controls left and right. The one on the outside angles it up and down.
    • Aim the light at a wall 20 feet away.
    • The concentration of the low beam on the wall should be 1â€� below the bulb. And straight ahead.
    • The high beam concentration should line up with the low beam bulb.
  5. step : Replacing the Bumper Cover (6:12)
    • Reinstall the parking light.
    • Reconnect the fog lights.
    • Place the bumper into place and connect the clips on either side.
    • Replace the bolt inside the inner fender.
    • Replace the six bolts that secure the inner fender.
    • Repeat this on both sides. Use an awl to help line up the fender by pushing it through the screw holes.
    • Replace the five 3/8â€� bolts under the bumper cover.

Tools needed for replacement:

    Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Screwdrivers & Related

  • Phillips Head Screwdriver

  • Sockets - Metric

  • 10mm Socket

  • Sockets - SAE

  • 3/8 Inch Socket

  • Torx Drivers & Sockets

  • T15 Torx Driver

5.00/ 5.0
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
Just as I ordered! Be careful with the adjustment screws
This mounting bracket fit perfectly! Packed well and was delivered on time. My only issue was the adjustment screws/bolts were flimsy and the screws that secured the adjustment bolt easily stripped out of the plastic. Easy fix with a little longer of a screw. Additional advice - let the plastic pieces warm up in your house before installing - will allow for more "play" when installing.
January 15, 2018
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1993-1997Dodge Intrepid Dodge Intrepid Headlight Mounting Bracket Pair
Part #: 1ALHP00475

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

How-to Video:

(10:03 min)