1984-96 Chevy Corvette Wheel Bearing & Hub Assembly Timken 513020 - TKSHR00003

Warranty & Shipping
How-To & Tools
Product Reviews
Vehicle Fit



  • Brand New Timken Hub Assembly
  • Fits RH or LH REAR
  • Direct replacement
  • 3 bolt flange
  • Replaces dealer part numbers: 7466924, 7466945, 7470501, 7470502
  • Fits 5 Lug Wheel
  • Studs already installed
  • Built to strict quality control standards
  • Fits all Corvettes including: LT1 LT5 ZR-1

These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Item Condition: New

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser.

  1. step : Removing the Wheel (0:54)
    • Loosen the lug nut covers with a 19mm socket
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. step : Removing the Caliper Bracket (1:37)
    • Remove the washer and hub nut from the hub
    • Remove the hub nut with a 36mm socket or a 7/16 inch socket and impact wrench, or have an assistant hold the breaks and remove the bolt with a breaker bar
    • Loosen the top 18mm bolt from the brake caliper
    • Place an 18mm wrench on the bottom bolt
    • Attach and additional wrench to the 18mm wrench for extra leverage
    • Remove the top 18mm bolt
    • Pull the caliper aside
  3. step : Removing the Brake Rotor (3:35)
    • Pull the rotor off
    • If the rotor will not come off, thread a lug nut and strike the hub area of the rotor with the ball end of a ball peen hammer
  4. step : Removing the Bearing Hub (4:05)
    • Spray the back side of the three Torx bolts on the hub with penetrating oil
    • Line up the hole with an impact tool on the backside of the bolt and it hit with a ball peen hammer
    • Remove the two lower T55 Torx bolts with a 3/8 breaker bar and a piece of pipe for leverage
    • Jack up the leaf spring
    • Straighten the cotter pin out with pliers
    • Remove the cotter pin
    • Use a 21mm socket and ratchet on top and a 22mm socket and ratchet on the bottom
    • Remove the 22mm nut from the link rod
    • Loosen the jack on the leaf spring
    • Jack up the suspension underneath the knuckle
    • Remove the T55 Torx bolt with a ratchet and piece of pipe for leverage
    • Place the teeth of a two-jaw puller around the hub flange
    • Tighten the puller into the hub
    • Loosen the puller
    • Remove the hub, backing plate, and emergency brake
    • Remove the hub from the backing plate
  5. step : Installing the Bearing Hub (8:09)
    • Hook the e-brake cable to the lever on the back of the backing plate
    • Insert the hub to the backing plate
    • Place it onto the axle
    • Push the T55 Torx bolts through and tighten each one preliminarily
    • Torque the top rear Torx bolt to 65 foot-pounds
    • Remove the jack from underneath the suspension
    • Raise the leaf spring with the jack
    • Tighten the 22mm nut on the link rod
    • Reinsert the cotter pin
    • Twist the ends of the cotter pin with a pair of pliers
    • Tighten the lower rear and front Torx bolts to 65 foot-pounds
  6. step : Reinstalling the Brake Rotor (10:35)
    • Slide the rotor on
    • Tighten the washer and hub nut preliminarily
  7. step : Reinstalling the Brake Caliper (10:55)
    • Put the caliper on
    • Thread the top bolt by hand
    • Tighten the lower bolt preliminarily using an 18mm wrench
    • Tighten bolts between 55 to 60 foot-pounds
    • Set the emergency brake
    • Torque the hub nut to 160 foot-pounds
  8. step : Reattaching the Wheel (11:53)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Tighten the lug nut covers with a 19mm socket
    • Pump the brakes a few times to ensure a firm pedal

Tools needed for replacement:

    General Tools

  • Flashlight
  • Assistant
  • Center Punch
  • Floor Jack
  • Jack Stands
  • Hammer

  • Materials, Fluids, and Supplies

  • Rust Penetrant

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • 1/2 Inch Ratchet
  • 1/2 Inch Breaker Bar
  • Torque Wrench
  • Socket Extensions
  • A Piece of Pipe (for leverage)

  • Sockets - Metric

  • 21mm Socket
  • 36mm Socket
  • 19mm Socket
  • 22mm Socket

  • Sockets - SAE

  • 7/16 Inch Socket

  • Torx Drivers & Sockets

  • T55 Torx Socket

  • Wrenches - Metric

  • 18mm Wrench

5.00/ 5.0
5 Stars
4 Stars
3 Stars
2 Stars
1 Star
New wheel bearings for 1991 Corvette
The Timken Wheel Bearing supplied by 1-A auto fit as advertised and has solved my problem with worn wheel bearings. Great value and great product
June 22, 2017
Will this fit my car? Add a vehicle to make sure
Customer Q&A
Ask a question to 1A Auto customers who purchased the product
No questions have been asked about this item.
Year Make Model Description
1984-1996Chevy Corvette Chevy Corvette Wheel Bearing & Hub Assembly Rear Timken 513020
Only 2 left in stock
Part #: TKSHR00003

Order must be placed by 4pm ET
Delivery options for:

Estimated Arrival Cost

Deliveries made to PO Boxes and FPO may take longer. See our Shipping & Delivery for more information.

Get it in: 2 - 4 Business Days

Want it sooner? Choose Next Day Air at Checkout

Brand #: 513020

How-to Video:

(13:03 min)