Replaces

1992-2011 Ford Crown Victoria Power Window Regulator with Motor Rear Pair (High Quality)

Part Details

  • Part Type: High Quality
  • Operation: Power
  • Front / Rear Location: Rear
  • Quantity: Pair
  • Part Type: Motor

This part replaces:

  • OE # 6W7Z5427009AA
  • OE # F2VZ54233V95ARM

  • New

These power window regulators are just what you need to get your vehicle in good working form again!

Specifications:

  • Comes as a PAIR
    • Fits both the LH (Driver Side) & RH (Passenger Side) REAR
  • Power operation
  • Replaces dealer part numbers: 6W7Z-5427008-AA, 6W7Z-5427009-AA, F2VZ-54233V94-ARM, F2VZ-54233V95-ARM, 6W7Z5427008AA, 6W7Z5427009AA, F2VZ54233V94ARM, F2VZ54233V95ARM
  • Include the power window motors
  • Direct replacements
  • Built to strict quality control standards

These power window regulators are great replacements that offer good cost savings over the dealer parts!

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Door Panel (1:03)
    • Pry up the switch panel with a flat blade screwdriver
    • Remove the Phillips head screws from the window switch harness
    • Pry out on the switch with a flat blade screwdriver
    • Pry off the bezel with a flat blade screwdriver
    • Pry off the two trim covers on the pull handle
    • Remove the two Phillips screws from the pull handle
    • Remove the Phillips screw from behind the switch panel
    • Remove the Phillips screw on the bottom of the door panel
    • Lift the panel up and off
    • Carefully pull off the water shield
  2. Removing the Rear Inside Door Handle (3:07)
    • Remove the Phillips screw from the door handle
    • Slide the handle forward and pull it out
    • Remove the door handle rod from the inside door handle
  3. Removing the Window Regulator (3:32)
    • Punch out the center of the rivets on the window motor with a hammer and punch
    • Punch out the rivets on the regulator
    • Punch out the rivets on the window
    • Drill out the rivets with a 3/8 bit
    • Remove the two 11mm bolts from the bottom of the regulator
    • Lower the window
    • Pull off the weatherstrip and trim around the window frame
    • Lift the secondary window up and out
    • Push the secondary window down and its weather strip down from the window frame
    • Raise the window by hand
    • Remove the window
    • Remove the two 11mm nuts on the top of the door
    • Disconnect the window motor lead
    • Pull the window regulator out through the door
  4. Reinstalling the Regulator (11:25)
    • Insert one of the bolts into the window regulator
    • Push the regulator into the door
    • Hang the regulator by the 11mm bolts in the regulator rail
    • Insert the two bolts into the window track
    • Insert the three bolts to the motor
    • Pry off the old rivets from the window with a flat blade screwdriver
    • Lower the window onto the regulator
    • Insert the two bolts into the bottom of the regulator
    • Lower the secondary window into place
    • Lift the window into place
    • Insert the two bolts that hold the window to the regulator
    • Put the weatherstrip and trim into place
  5. Installing the Rear Inside Door Handle (17:08)
    • Insert the door handle rod to the inside door handle
    • Slide the door handle back
    • Tighten the Phillips screw to the door handle
  6. Reinstalling the Door Panel (17:23)
    • Put the water shield in place
    • Lift the door panel into place
    • Insert the longer Phillips screw behind the switch panel
    • Insert the longer Phillips screw to the bottom of the door panel
    • Insert the two Phillips screws to the pull handle
    • Push the switch into the switch panel
    • Push the switch panel in place
    • Push in the door handle bezel
    • Push in the trim buttons on the pull handle

Tools needed for replacement:

    Drills, Drill Bits & Related

  • 3/8 Inch Drill Bit
  • Drill

  • Materials, Fluids, and Supplies

  • Coarse Threaded Bolts (to replace rivets)

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 11mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(19:34 min)

Tools List:

    Drills, Drill Bits & Related

  • 3/8 Inch Drill Bit
  • Drill

  • Materials, Fluids, and Supplies

  • Coarse Threaded Bolts (to replace rivets)

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 11mm Socket



This part replaces:

  • OE # 6W7Z5427009AA
  • OE # F2VZ54233V95ARM

Vehicle Fit

  • 1992-2011 Ford Crown Victoria Power Window Regulator with Motor Rear Pair (High Quality)
  • 1992-2010 Mercury Grand Marquis Power Window Regulator with Motor Rear Pair (High Quality)
  • 2003-2004 Mercury Marauder Power Window Regulator with Motor Rear Pair (High Quality)
$101.45
Save 42%
List: $175.95 Save: $74.50
Part #: 1AWRK00116

Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est