Replaces

2003-2004 Mercury Marauder Power Window Regulator with Motor Front Driver Side (High Quality)

Part Details

  • Part Type: High Quality
  • Window Options: with Motor
  • Operation: Power
  • Location: Front
  • Location: Driver Side

This part replaces:

  • DORMAN 741-664
  • OE # 6W7Z5423209AA, F2VZ54233V94ARM
  • PARTSLINK FO1350106 + Motor

  • New

Specifications:

  • LH (Driver Side) FRONT
  • Power operation
  • Replaces dealer part numbers: 6W7Z-5423209-AA, F2VZ-54233V94-ARM, 6W7Z5423209AA, F2VZ54233V94ARM
  • Includes the power window motor
  • Direct bolt on replacement
  • Built to strict quality control standards

Please Note: This High Quality power window regulator is a new aftermarket replacement part that is built to strict quality control standards. It is far superior to the lower quality window regulators which have begun to appear on the internet. Although this window regulator is produced overseas, it was designed in the U.S. and the tooling is owned by a large U.S. manufacturer. That is why we guarantee this high quality window regulator with a superior warranty! If price is your main concern, we do offer the lower price overseas designed and built window regulator in our other listings.

Installation

  • This repair is easier than you may think. You'll find our installation videos helpful. In our experience removing and replacing the door panel is the most involved step in the repair. On most vehicles this only requires removing a few screws and push in clips.
  • You'll get a great feeling of accomplishment after you complete this repair knowing you saved money, and you didn't have to give up your car for a day at the repair shop. Your passengers and other drivers will be amazed.

Fit guaranteed

  • 1A Auto will refund you with no hassle, if this Window regulator does not fit the application stated.
    • You can use your existing hardware and wiring harnesses. This Regulator will install just as your original does. Save time and money.

Quality

  • Be confident this part will work right. Every regulator is tested after assembly to make sure all mechanisms are working correctly.
  • It is important that your new regulator works for a long period of time. The design of this regulator is tested to withstand 10,000 cycles. That is enough to raise and lower your window 3 times per day for 9 years.
  • Nothing is more frustrating than taking your car apart and finding the part you purchased does not fit. You want the part to fit. This design is test fit on an actual door. When you install it, you will have no issues.

Value

  • Windows that don't work can be frustrating. They can also hurt your vehicles value. An inoperable window could mean $200-$500 discounted off a dealer trade value or asking price.
  • Some shops and dealers charge more for parts and repairs when they think you don't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly repair bill.

 

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Step 1:Remove the Door Panel (0:48 in the video)
    • Using a flat blade screwdriver pry up the switch panel.
    • Pry of the mirror switch.
    • Disconnect all the wire harnesses from the switch panel.
    • Remove the caps from the pull handle to uncover the screws.
    • Using the area at the top of the door handle panel pry the panel off.
    • Remove the five Phillips screws on the door panel.
    • Lift the door panel up and out.
    • Disconnect the wiring harnesses to get the panel free.
  2. Step 2: Accessing the Window Regulators (4:06 in the video)
    • Remove the three screws on the speaker and pull it free. Disconnect the wire harness on the back.
    • Remove the junction block below this, by removing the screw.
    • Carefully pull the door handle down and out of the way.
  3. Step 3: Removing the Window Regulator (4:38 in the video)
    • Place a punch on the center of the rivets and use a hammer to punch the center out.
    • Move your window up.
    • Remove the inside door handle. Disconnect it from the door rod.
    • Knock the center of the rivets out on the actual regulator.
    • Use a 3/8 drill bit to drill out each of the rivets. Do this slowly and carefully.
    • Disconnect the wiring harness linked to the window motor.
    • Remove the weather strip at the bottom of the window.
    • Remove the window rivets.
    • Let the window down. Tilt the nose down and pull up to free the window from the door.
    • Remove the two 11mm bolts at the top of the door.
    • Pull the window regulator out of the door.
  4. Step 4: Replacing the Window Regulator (9:48 in the video)
    • Fit the regulator into the door.
    • Hang the regulator into place using the top studs. Put the nuts on to secure them.
    • With hardware s bought bolts washer and nuts, secure the regulator. These replace the rivets.
    • Connect the regulator wiring harness.
    • Tighten the regulator bolts and nuts.
    • Make sure the window is clear of the old rivets. Use pliers and screwdrivers to pry the remnants free.
    • Put the window in nose first and tilt the back down in.
    • Slide the window into the rail.
    • Put bolts into the holes to secure the window to the regulator.
    • Plug in the window switch panel.
    • Test the window before reapplying the door panel.
  5. Step 5: Reapplying the Door Panel (15:10 in the video)
    • Reinsert the weather strip.
    • Put the inner door handle back into place and replace the screw.
    • Disconnect the window switch panel.
    • Reposition the water shield.
    • Screw the speaker back into place.
    • Screw the junction block back into place.
    • Reconnect the harnesses to the back of the door panel.
    • Pull the door panel up and of the lock and snap down into place.
    • Reinsert the five Phillips screws.
    • Reconnect the switch panel. And snap it into place.
    • Put the interior door handle panel back into place.
    • Put the pull handle caps back into place.

Tools needed for replacement:

    Drills, Drill Bits & Related

  • 3/8 Inch Drill Bit
  • Drill

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 11mm Socket

  • Specialty Tools

  • Center Punch
  • Hammer

How-to Video:

(18:52 min)

Tools List:

    Drills, Drill Bits & Related

  • 3/8 Inch Drill Bit
  • Drill

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Phillips Head Screwdriver

  • Sockets - Metric

  • 11mm Socket

  • Specialty Tools

  • Center Punch
  • Hammer



This part replaces:

  • DORMAN 741-664
  • OE # 6W7Z5423209AA, F2VZ54233V94ARM
  • PARTSLINK FO1350106 + Motor

Vehicle Fit

  • 1992-2011 Ford Crown Victoria Power Window Regulator with Motor Front Driver Side (High Quality)
  • 1992-2010 Mercury Grand Marquis Power Window Regulator with Motor Front Driver Side (High Quality)
  • 2003-2004 Mercury Marauder Power Window Regulator with Motor Front Driver Side (High Quality)
$70.45
Save 73%
List: $260.00 Save: $189.55
Part #: 1AWRG00254

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est