Replaces

2000-2000 Chevy Impala Front Wheel Hub & Outer Tie Rod for Models with ABS

Part Details

  • Location: Front

  • New

This replacement wheel hub & tie rod kit is just what you need to get your vehicle in good working order again.

Wheel Hub Specifications:

  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • Replaces dealer part numbers: 7470017, 7470105, 7470143, 7470567, 7470568, 12429204
  • Wheel studs already included and installed!
  • Has ABS sensor w/stainless steel sensor wire clip
  • Direct replacement
  • Built to strict quality control standards

Tie Rod Specifications:

  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT OUTER
  • Replaces dealer part numbers: 26056811, 26086580
  • Direct replacement
  • Built to strict quality control standards
NOTE: This listing is for one (1) hub assembly and one (1) tie rod, enough to do one side of the vehicle. For a pair, please check our other listings.

It is very important when installing to tighten the Hub Nut to 118 foot lbs. Failure to use the correct torque specifications will result in premature failure of the hub.

NOTE: For 2001 Models: Replaces hub assemblies with Stainless Steel Sensor Wire Clip. Does not replace hub assemblies with a Plastic Clip.

2 Year Warranty

This item is backed by a 2 Year Warranty. In the event this item should fail during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Wheel (0:45 in the video)
    • Remove the lug nut covers with a 19mm socket
    • Pull off the hub cap
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. Removing the Outer Tie Rod (1:18 in the video)
    • Twist the cotter pin out of the tie rod nut with needle nose pliers
    • Remove the 18mm nut from the tie rod
    • Measure from the boot of the inner tie rod to the center of the outer tie rod
    • Note this measurement
    • Loosen the 7/8 inch nut that holds the inner to the outer tie rod
    • Thread the 18mm nut onto the tie rod slightly
    • Strike the tie rod with a hammer to loosen it from the spindle
    • Twist off the outer tie rod
  3. Installing the New Outer Tie Rod (2:32 in the video)
    • Attach the grease fitting to the new outer tie rod
    • Tighten the grease fitting with a 7mm socket and ratchet
    • Twist the outer tie rod onto the inner tie rod
    • Push the tie rod into the spindle
    • Thread the 18mm nut onto the tie rod
    • Measure the distance from the boot to the center of the tie rod
    • This measurement should match the one taken in Step 2
    • Adjust the tie rod as necessary
    • Tighten the 18mm nut
    • Put the cotter pin through the 18mm nut and fold it over with needle nose pliers
    • Hold the nut that connects the inner to the outer tie rod with a 7/8 inch wrench
    • Turn the inner tie rod with a 13mm wrench
    • Add grease to the grease fitting with a grease gun
  4. Reattaching the Wheel (3:58 in the video)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Put on the hub cap, lining up the hole with the valve stem
    • Tighten the lug nut covers with a 19mm socket

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Bearing Grease

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Sockets - Metric

  • 18mm Socket
  • 19mm Socket
  • 7mm Socket

  • Specialty Tools

  • Floor Jack
  • Jack Stands
  • Measuring Tape

  • Wrenches - Metric

  • 13mm Wrench
  • 22mm Wrench

  • Wrenches - SAE

  • 7/8 Inch Wrench

How-to Video:

(04:49 min)

Tools List:

    Materials, Fluids, and Supplies

  • Bearing Grease

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Ratchet

  • Sockets - Metric

  • 18mm Socket
  • 19mm Socket
  • 7mm Socket

  • Specialty Tools

  • Floor Jack
  • Jack Stands
  • Measuring Tape

  • Wrenches - Metric

  • 13mm Wrench
  • 22mm Wrench

  • Wrenches - SAE

  • 7/8 Inch Wrench




Vehicle Fit

  • 1997-2000 Buick Century Front Wheel Hub & Outer Tie Rod for Models with ABS
  • 2001 Buick Century Front Wheel Hub & Outer Tie Rod for Models with Stainless Steel Sensor Wire Clip & with ABS
  • 1997-2000 Buick Regal Front Wheel Hub & Outer Tie Rod for Models with ABS
  • 2001 Buick Regal Front Wheel Hub & Outer Tie Rod for Models with Stainless Steel Sensor Wire Clip & with ABS
  • 2000 Chevy Impala Front Wheel Hub & Outer Tie Rod for Models with ABS
  • 2001 Chevy Impala Front Wheel Hub & Outer Tie Rod for Models with Stainless Steel Sensor Wire Clip & with ABS
  • 2000 Chevy Monte Carlo Front Wheel Hub & Outer Tie Rod for Models with ABS
  • 2001 Chevy Monte Carlo Front Wheel Hub & Outer Tie Rod for Models with Stainless Steel Sensor Wire Clip & with ABS
  • 1998-2000 Olds Intrigue Front Wheel Hub & Outer Tie Rod for Models with ABS
  • 2001 Olds Intrigue Front Wheel Hub & Outer Tie Rod for Models with Stainless Steel Sensor Wire Clip & with ABS
$60.45
Part #: 1AHTF00006

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est