Replaces

2004-2005 Honda Civic Front Wheel Bearing Pair (excluding SI Models)

Part Details

  • Front / Rear Location: Front
  • Quantity: Pair

  • New

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) FRONT
  • Replaces dealer part number: 44300-S5A-008, 44300S5A008
  • Bearings only, do Not include the hubs
  • Direct replacements
  • Built to strict quality control standards

2 Year Warranty

This item is backed by a 2 Year Warranty. In the event this item should fail during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Wheel (0:55)
    • Loosen the 19mm lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. Removing the Hub Nut (1:25)
    • Remove the dust cap with a chisel and hammer
    • Insert a tapered punch into the punched slit between the retainer and nut
    • Tap the punch to separate the nut
    • Remove the 32mm nut axle nut with a pry bar and breaker bar
  3. Removing the Caliper (1:52)
    • Remove the 17mm bolts from the caliper bracket
    • Remove the caliper and caliper brackets assembly from the rotor
    • Hand the caliper with a wire tie or bungee
  4. Separating the Ball Joint (2:28)
    • Bend the cotter pin tab out with needle nose pliers
    • Pry the cotter pin out
    • Remove the 17mm castle nut on the bottom of the ball joint
    • Tap up with a hammer to release the ball joint
    • Use a pickle fork to separate the ball joint if needed
  5. Removing the Spindle (3:45)
    • Remove the 22mm bolts from the bottom of the strut
    • Unbolt the wheel speed sensor with a 10mm socket and ratchet
    • Remove the sensor with a pair of pliers
    • Tap the center of the CV axle
    • Pull the axle out of the spindle
  6. Removing the Backing Plate and Hub (5:04)
    • Insert the hub and rotor into the hydraulic press
    • Press the hub out of the bearing
    • Remove the three Phillips screws from the backing plate
    • Remove the backing plate
  7. Removing the Bearing (5:37)
    • Squeeze the snap ring with snap ring pliers
    • Pry the snap ring out with a flat blade screwdriver
    • Press the bearing out with a hydraulic press
  8. Installing the Bearing (6:15)
    • Press the bearing into the knuckle with a hydraulic press
    • Attach the snap ring to a pair of snap ring pliers
    • Press the snap ring into the bearing
  9. Installing the Backing Plate and Hub (6:28)
    • Insert the backing plate to the knuckle
    • Tighten the three Phillips screws to the backing plate
    • Place the old bearing on the back of the inner bearing for support
    • Place the spindle into the hydraulic press
    • Insert the hub into the spindle with the hydraulic press until it bottoms out
  10. Installing the Spindle (7:04)
    • Insert the lower ball joint into the control arm
    • Line up and press the CV Axle into the hub
    • Insert the 22mm bolts (head facing front of car) into the bottom of the strut
    • Torque the strut bolts to 116 foot-pounds with a 19mm wrench on the bolt side
  11. Installing the Hub Nut (8:34)
    • Insert the hub nut into place
    • Torque the 32mm hub nut to 134 foot-pounds with a pry bar to keep the hub still
    • Dent the outer ring on the axle nut into the keeper groove with a hammer and pick
    • Tighten the 10mm bolt to the wheel speed sensor
  12. Installing the Ball Joint (9:38)
    • Align the castle nut with the windows on the control arm
    • Torque the castle nut to 43-50 foot-pounds
    • Insert the cotter pin into nut
    • Bend the cotter pin underneath
  13. Reinstalling the Brake Caliper (10:33)
    • Insert the brake rotor into place
    • Tighten the Number 2 Phillips screw to the brake rotor
    • Spread the pads and insert the caliper into place
    • Tighten the 17mm caliper bolts
    • Torque the caliper bolts to 80 foot-pounds
  14. Reattaching the Wheel (11:45)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the 19mm lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 80 foot-pounds in a crossing or star pattern

Tools needed for replacement:

    General Tools

  • Jack Stands
  • Center Punch
  • Hammer
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 32mm Socket
  • 19mm Socket
  • 17mm Socket
  • 22mm Socket
  • 10mm Socket

There are no reviews for this item. Write Review
Start typing your question and we'll check if it was already asked and answered. Learn More
No questions have been asked about this item. Be the first!

How-to Video:

(12:29 min)

Tools List:

    General Tools

  • Jack Stands
  • Center Punch
  • Hammer
  • Floor Jack

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • Torque Wrench
  • 1/2 Inch Breaker Bar

  • Screwdrivers & Related

  • Pry Bar
  • Phillips Head Screwdriver
  • Flat Blade Screwdriver

  • Sockets - Metric

  • 32mm Socket
  • 19mm Socket
  • 17mm Socket
  • 22mm Socket
  • 10mm Socket




Vehicle Fit

  • 1994-2001 Acura Integra Front Wheel Bearing Pair
  • 1992-2000 Honda Civic EX & SI Front Wheel Bearing Pair
  • 2001-2003 Honda Civic Front Wheel Bearing Pair
  • 2004-2005 Honda Civic Front Wheel Bearing Pair (excluding SI Models)
  • 1994-1997 Honda Civic Del Sol Front Wheel Bearing for Models with ABS Pair
  • 2003-2005 Honda Civic Hybrid Front Wheel Bearing Pair
$ 42.95
Save 76%
List: $176.16 Save: $133.21
Part #: 1ASHS00242

Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY M-F
For Orders Placed By 5pm Est