Replaces

2002-2005 Mercury Mountaineer Front Wheel Bearing & Hub Assembly Pair (Timken)

This part replaces:

  • Timken SP470200

  • New

TIMKEN WHEEL BEARING & HUB ASSEMBLY PAIR: SP470200

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly PAIR
  • Comes as a PAIR
    • Fits both the LH (Driver Side) & RH (Passenger Side) FRONT
  • 3 Bolt Flanges
  • Fit 5 Lug Wheels
  • Replaces dealer part numbers: 1L24-1104AC, 1L24-1104AD, 1L24-1104AE, 1L24-1104AF, 1L24-1104AG, 1L24-1K018AB, 1L2Z-1104AA, 1L2Z-1104AB, 2L24-1104AA, 2L24-1K018AB, 2L2Z-1104AA, 2L2Z-1104AB, 3L24-1K018AA, 3L24-1K018AB, 3L2Z-1104AB, 4L2Z-1104AA, 1L241104AC, 1L241104AD, 1L241104AE, 1L241104AF, 1L241104AG, 1L241K018AB, 1L2Z1104AA, 1L2Z1104AB, 2L241104AA, 2L241K018AB, 2L2Z1104AA, 2L2Z1104AB, 3L241K018AA, 3L241K018AB, 3L2Z1104AB, 4L241K018AA, 4L2Z1104AA, 3C5Z 1104 AA, 3C5Z1104AA
  • Studs already installed
  • Include ABS sensors and plug wires
  • Direct replacements
  • Built to strict quality control standards

These wheel bearing & hub assemblies are great replacements and have good cost savings over units from the dealer.

Note: These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hubs & bearings are all tested prior to shipping.

Fit Guaranteed

  • These hub & bearing sets will install just as your originals do. You can use your existing hardware.
  • Save time and money with direct fit hub bearing assemblies. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

 

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Wheel (0:48)
    • Pry off the center cap with a flat blade screwdriver
    • Remove the hub nut with a 30mm socket and ratchet
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. Removing the Brake Pads (1:33)
    • Pry the ABS sensor wiring out of its clips with a flat blade screwdriver
    • Remove the two 14mm bolts from the brake caliper
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
    • Hold the brake caliper aside with wire ties
    • Pry the brake pads off with a flat blade screwdriver
  3. Removing the Brake Rotor (3:19)
    • Remove the two 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Pull the rotor off
  4. Removing the Hub (3:40)
    • Disconnect the ABS sensor wiring harness in the engine compartment
    • Unclip the ABS sensor wiring
    • Pull out the ABS sensor wire
    • Make sure the axle can move freely in and out of the hub
    • Apply rust penetrant to the hub bolts
    • Remove the three 15mm bolts from the hub
    • Pull off the hub
  5. Installing the Hub (5:37)
    • Push the hub onto the axle with the ABS sensor on top
    • Insert the three 15mm bolts into the hub
    • Tighten the hub bolts to 75 foot-pounds of torque
    • Feed the ABS sensor wire into place
    • Fasten the hub nut onto the hub
  6. Installing the Brake Rotor (7:40)
    • Slide the rotor on
    • Thread on one lug nut to hold the rotor in place
    • Put the bracket back into place
    • Start the two 18mm bolts by hand
    • Tighten the bolts to 85 foot-pounds
  7. Installing the Brake Pads (8:27)
    • Apply brake grease to the brake pad tabs
    • Install the new brake pads into the bracket
    • Remove the wire ties from the caliper
    • Put the caliper on
    • Thread the two 14mm bolts by hand
    • Tighten bolts to 25 foot-pounds
    • Push the ABS sensor wire into its clips
    • Clean the brake rotor
  8. Reattaching the Wheel (10:04)
    • Remove the placeholder lug nut
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the hub nut to 180 foot-pounds
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
  9. Connecting the ABS Sensor (10:50)
    • Connect the ABS sensor wiring harness inside the engine compartment
  10. Testing the Brakes (11:03)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    Allen Wrenches

  • 5mm Allen Wrench

  • General Tools

  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • White Grease

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 15mm Socket
  • 18mm Socket
  • 19mm Socket
  • 30mm Socket

How-to Video:

(11:32 min)

Tools List:

    Allen Wrenches

  • 5mm Allen Wrench

  • General Tools

  • Floor Jack
  • Jack Stands

  • Materials, Fluids, and Supplies

  • White Grease

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 14mm Socket
  • 15mm Socket
  • 18mm Socket
  • 19mm Socket
  • 30mm Socket



This part replaces:

  • Timken SP470200

Vehicle Fit

  • 2002-2005 Ford Explorer 4 Door Front Wheel Bearing & Hub Assembly Pair (excluding Sport Trac Models) (Timken)
  • 2003-2005 Lincoln Aviator Front Wheel Bearing & Hub Assembly Pair (Timken)
  • 2002-2005 Mercury Mountaineer Front Wheel Bearing & Hub Assembly Pair (Timken)
$325.45
Save 46%
List: $600.00 Save: $274.55
Only 2 left in stock
Part #: TKSHS00027

Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates
Timken
Brand #: SP470200

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est