Replaces

2008-2013 Audi TT Quattro Rear Wheel Bearing & Hub Assembly Pair (Timken)

Part Details

  • Front / Rear Location: Rear

This part replaces:

  • Timken HA590106

  • New

TIMKEN WHEEL BEARING & HUB ASSEMBLY PAIR: HA590106

These replacement hub & bearing assemblies just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assemblies
  • Comes as a PAIR
    • Fits either LH (Driver Side) or RH (Passenger Side) REAR
  • Replaces dealer part numbers: 8J0 598 625, 8J0598625, 3C0 498 621, 3C0498621, 1K0407621G, 1K0 407 621G, 1T0498621, 1T0 498 621
  • Direct replacement for bolt on Hub & Bearings
  • 4 Bolt Flanges
  • Fits 5 lug wheels
    • Wheel studs are not included
  • Fits Quattro or AWD (All Wheel Drive) Models only

 

Note: These parts are authentic Timken brand products that are supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hubs & bearings are all tested prior to shipping.

Fit Guaranteed

  • These hub & bearing sets will install just as your originals do. You can use your existing hardware.
  • Save time and money with direct fit hub bearing assemblies. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

 

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Wheel (0:50)
    • Pry off the center cap with a flat blade screwdriver
    • Pry off the lug bolt covers with a pick
    • Loosen the 27mm hub bolt
    • Loosen the locking lug bolt with the key
    • Loosen the lug bolts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug bolts
    • Pull off the wheel
  2. Removing the Brake Pads (1:44)
    • Pry off the caliper bolt plugs by hand
    • Remove the two T47 Torx bolts from the brake caliper
    • Pry the caliper clip off with a flat blade screwdriver
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Pull the caliper aside
  3. Removing the Brake Rotor (2:37)
    • Remove the two 21mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Remove the T30 bolt from the rotor
    • Apply rust penetrant to the hub
    • Thread in one lug bolt
    • Strike the back of the rotor with a hammer to loosen it
    • Pull the rotor off
  4. Removing the Hub (3:33)
    • Remove the 27mm hub nut
    • Thread in the hub bolt half way
    • Strike the hub bolt with a hammer to loosen the axle
    • Remove the hub bolt
    • Remove the three 16mm nuts from the control arm
    • Pry down the control arm with a pry bar
    • Tap the axle out of the hub with a hammer and a socket
    • Remove the four 12-point 12mm bolts from the hub
    • Thread one 12mm bolt half way into the hub
    • Tap the hub with a hammer to loosen it
  5. Installing the Hub (5:20)
    • Put the hub into place
    • Insert the 12mm bolts into the hub
    • Tighten the 12mm bolts to 50 foot-pounds of torque
    • Turn each hub bolt an extra 1/4- turn
    • Push the axle into place
    • Push the control arm onto its studs
    • Fasten the three 16mm nuts onto the control arm
    • Tighten the three 16mm nuts to 50 foot-pounds
    • Thread on the hub bolt by hand
  6. Installing the Brake Rotor (7:06)
    • Slide the rotor on
    • Insert the T30 bolt into the rotor
    • Put the bracket back into place
    • Start the two 21mm bolts by hand
    • Tighten the 21mm bolts to 90 foot-pounds
  7. Installing the Brake Pads (8:01)
    • Put the brake pads into the caliper bracket if they are not already installed
    • Put the caliper on
    • Insert the two T47 bolts into the caliper
    • Tighten the T47 bolts to 30 foot-pounds
    • Push on the wire caliper bracket clip
    • Push on the caliper bolt plugs
  8. Reattaching the Wheel (8:44)
    • Slide the wheel into place
    • Start the lug bolts by hand
    • Tighten the lug bolts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug bolts to 100 foot-pounds in a crossing or star pattern
    • Push on the lug bolt caps
    • Tighten the hub bolts to 150 foot-pounds
    • Reattach the center cap

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Pick

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 12mm 12-Point Socket
  • 16mm Socket
  • 17mm Socket
  • 21mm Socket
  • 27mm socket

How-to Video:

(10:06 min)

Tools List:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Pick

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver
  • Pry Bar

  • Sockets - Metric

  • 12mm 12-Point Socket
  • 16mm Socket
  • 17mm Socket
  • 21mm Socket
  • 27mm socket



This part replaces:

  • Timken HA590106

Vehicle Fit

  • 2006-2013 Audi A3 Quattro Rear Wheel Bearing & Hub Assembly Pair (Timken)
  • 2008-2013 Audi TT Quattro Rear Wheel Bearing & Hub Assembly Pair (Timken)
  • 2009-2013 VW CC Rear Wheel Bearing & Hub Assembly for VR6 Models 4 Motion Models Pair (Timken)
  • 2006-2010 VW Passat Rear Wheel Bearing & Hub Assembly for 4 Motion Models Pair (Timken)
  • 2008 VW R32 Rear Wheel Bearing & Hub Assembly Pair (Timken)
  • 2009-2013 VW Tiguan Rear Wheel Bearing & Hub Assembly Pair (Timken)
$314.95
Save 23%
List: $410.00 Save: $95.05
Only 4 left in stock
Part #: TKSHS00572

Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates
Timken
Brand #: HA590106

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est