Replaces

2004-2005 Buick Century Rear Wheel Bearing & Hub Assembly Pair

Part Details

  • Front / Rear Location: Rear
  • Quantity: Pair

  • New

Specifications:

  • Comes as a PAIR
    • Fits both LH (Driver Side) & RH (Passenger Side) REAR
  • 4 Bolt Rectangular Flanges
  • Fit 5 Lug Wheels
  • Replaces dealer part number: 12413029
  • Studs already installed
  • Direct replacements
  • Built to strict quality control standards
  • Fits models WITHOUT ABS (Anti-Lock Brakes)

Note: If your vehicle requires a match to an RPO (Regular Production Option) code, you can usually find it on your original window sticker and sometimes either on the inside of your trunk lid, spare tire cover, glove box door, or the front driver's side door shell.

2 Year Warranty

This item is backed by a 2 Year Warranty. In the event this item should fail during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Wheel (0:47 in the video)
    • Loosen the lug nut covers with a 19mm socket
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. Removing the Rotor (1:11 in the video)
    • Remove the 13mm bolts from the brake caliper
    • Pry the caliper off with a flat blade screwdriver
    • Remove the rotor
    • Rotate the hub and remove the four 10mm bolts
  3. Removing the E-Brake Shoes (2:20 in the video)
    • Pry the e-brake shoe out of the adjustor with a flat blade screwdriver
    • Remove the tab from the other side of the adjustor keeping the pill inside
    • Angle the E-brake shoe down and around the hub
    • Remove the E-brake shoe
  4. Removing the Hub (2:51 in the video)
    • Pry out the spring from below the hub and unhook it
    • Unhook the lever from the cable and pull it down and out
    • Pry out on the clip on the parking brake cable and pull the cable free
    • Remove the two T30 bolts from the hub
    • Hammer the hub while pulling on it
    • Pull the hub free
  5. Installing the New Hub (4:23 in the video)
    • Clean the inside of the knuckle with a wire brush
    • Place the backing plate into the hub
    • Insert the hub into place
    • Replace the upper 10mm bolts by hand and tighten them
    • Insert the adjustor
    • Replace the two lower 10mm bolts on the hub
    • Insert and tighten the two T30 Torx bolts
    • Re-clip the parking brake cable
    • Push the lever into the adjustor and re-clip the cable to the lever
    • Clip in the spring and pry it into place with a flat blade screwdriver
    • Torque the hub bolts to 50 ft/lbs
  6. Reinstalling the E-Brake Shoes (7:13 in the video)
    • Push the brake shoe back down and around the hub with a flat blade screwdriver
    • Push the cap on the adjustor into place
    • Push the E-brake shoes into the clip and the 10mm bolts
    • Push the E-brake into the two slots on either side of the adjustor
    • Line up the slots on the adjustor with the tabs on the brake shoe
    • Adjust the adjustor with a hammer and flat blade screwdriver bringing the brake shoes in
  7. Installing the Rotor (8:22 in the video)
    • Place the rotor over the hub
    • Hammer the brake caliper back on
    • Replace and tighten the 13mm bolts on the caliper
  8. Reattaching the Wheel (8:52 in the video)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 ft/lbs in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket

Tools needed for replacement:

    Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 13mm Socket
  • 19mm Socket

  • Specialty Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Wire Brush

  • Torx Drivers & Sockets

  • T30 Torx Driver

  • Wrenches - SAE

  • 1/4 Inch Wrench

How-to Video:

(09:57 min)

Tools List:

    Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 13mm Socket
  • 19mm Socket

  • Specialty Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Wire Brush

  • Torx Drivers & Sockets

  • T30 Torx Driver

  • Wrenches - SAE

  • 1/4 Inch Wrench




Vehicle Fit

  • 2004-2005 Buick Century Rear Wheel Bearing & Hub Assembly Pair
  • 2003 Buick Regal Rear Wheel Bearing & Hub Assembly for Models with 4 Wheel Disc Brakes Pair
  • 2004 Buick Regal Rear Wheel Bearing & Hub Assembly Pair
  • 2003 Buick Rendezvous Rear Wheel Bearing & Hub Assembly for Models with Auto Level Control RPO Code G67 Pair (excluding All Wheel Drive Models)
  • 2000-2001 Chevy Impala Rear Wheel Bearing & Hub Assembly for Models with 4 Wheel Disc Brakes Pair
  • 2002-2005 Chevy Impala Rear Wheel Bearing & Hub Assembly Pair
  • 2000-2001 Chevy Monte Carlo Rear Wheel Bearing & Hub Assembly for Models with 4 Wheel Disc Brakes Pair
  • 2002-2005 Chevy Monte Carlo Rear Wheel Bearing & Hub Assembly Pair
  • 2003-2005 Pontiac Aztek Rear Wheel Bearing & Hub Assembly Pair (excluding All Wheel Drive Models)
  • 2003 Pontiac Grand Prix Rear Wheel Bearing & Hub Assembly Pair
$91.45
Save 89%
List: $798.00 Save: $706.55
Part #: 1ASHS00142

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est