Replaces

2006-2008 Chevy Impala Front & Rear Wheel Bearing & Hub Assembly (Set of 4) for Models with ABS

Part Details

  • Location: Front
  • Location: Rear
  • Quantity: Set of 4

  • New

Specifications:

  • Comes as a SET of 4
    • (2) - FRONT Hubs with 3 Bolt Triangular Flanges - LH (Driver Side) & RH (Passenger Side)
    • (2) - REAR Hubs with 4 Bolt Rectangular Flanges - LH (Driver Side) & RH (Passenger Side)
  • Fit 5 Lug Wheels
  • Replaces dealer part numbers: 12403095, 7467357, 7467587, 12413093, 12413094, 12413125, 12413126, 12413194, 88964168, 88964177
  • Studs already installed
  • Built to strict quality control standards
  • Fit models with ABS - RPO Code "JL9"
  • Have ABS sensors built in with correct plug configuration
  • Fit FWD (Front Wheel Drive) Models only
    • Do NOT fit AWD (All Wheel Drive) Models

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hubs & bearings are all tested prior to shipping.

Fit Guaranteed

  • These hub & bearing sets will install just as your originals do. You can use your existing hardware.
  • Save time and money with direct fit hub bearing assemblies. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

 

2 Year Warranty

This item is backed by a 2 Year  Manufacturers Warranty. In the event this item should fail during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Wheel
    • Loosen the lug nut covers with a 19mm socket
    • Pull off the center cap
    • Loosen the lug nuts with the vehicle on the ground
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. Removing the Brake Pads
    • Remove the two 14mm bolts from the brake caliper
    • Pull the caliper aside
    • Pull the brake pads off
  3. Removing the Brake Rotor
    • Remove the two 13mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Hold the rotor in place with a flat blade screwdriver
    • Remove the T30 Torx screw from the rotor
    • Strike the rotor with a hammer to loosen it
    • Pull the rotor off
  4. Removing the Wheel Hub
    • Remove the four 10mm bolts from the wheel hub
    • Disconnect the ABS wiring harness from the hub
    • Strike the hub with a hammer to remove it
    • Push out the emergency brake cable pin with a hammer and a screwdriver
    • Pull the spring off the brake backing plate with a screwdriver
    • Pull the emergency brake cable out of the brake backing plate
  5. Separating the Wheel Hub from the Brake Backing Plate
    • Remove the two T30 screws from the backing plate
    • Pull the bracket off of the backing plate
    • Pull the backing plate off of the hub
    • Pull the emergency brake ring off of the hub
  6. Preparing the New Wheel Hub
    • Clean the hub mounting area with a wire brush
    • Apply white grease or bearing grease to the mounting area
    • Put the emergency brake ring onto the backing plate
    • Put the hub through the ring and backing plate, making sure the ABS wiring connector is lined up with the backing plate hole
    • Pull the arm off the emergency brake activator
    • Put the emergency brake activator onto the ring
    • Attach the bracket to the backing plate
    • Insert the two T30 screws into the bracket
    • Push the emergency brake arm into place through the bracket
  7. Installing the New Wheel Hub
    • Attach the emergency brake cable to the emergency brake arm
    • Push the emergency brake cable into its bracket
    • Insert the pin into the bracket, using a hammer
    • Attach the spring to the emergency brake arm
    • Pull the spring onto the bracket with vise-grip pliers
    • Push the hub into place
    • Start one of the 10mm bolts to hold the hub in place
    • Start the remaining three 10mm bolts
    • Tighten the four 10mm bolts to 45 - 50 foot-pounds of torque
    • Reconnect the ABS wiring harness
    • Adjust the emergency brake, by turning the wheel with a flat blade screwdriver
  8. Reinstalling the Brake Rotor
    • Slide the rotor on
    • Adjust the emergency brake further, if necessary
    • Insert the T30 screw into the rotor
    • Put the bracket back into place
    • Start the two 13mm bolts by hand
    • Tighten the bolts to 75 foot-pounds of torque
  9. Reinstalling the Brake Pads
    • Apply grease to the brake pads
    • Install the new brake pads into the bracket
    • Put the caliper on
    • Thread the two 14mm bolts by hand
    • Tighten bolts to 30 foot-pounds
  10. Reattaching the Wheel
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to 100 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Tighten the lug nut covers with a 19mm socket

How-to Video:

(12:19 min)

Tools List:

    Materials, Fluids, and Supplies

  • Bearing Grease
  • White Grease

  • Pliers, Cutters & misc Wrenches

  • Vise Grip Pliers

  • Ratchets & Related

  • Breaker Bar
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 13mm Socket
  • 14mm Socket
  • 19mm Socket

  • Specialty Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Large C-Clamp
  • Wire Brush

  • Torx Drivers & Sockets

  • T30 Torx Driver




Vehicle Fit

  • 2005-2008 Buick Allure Front & Rear Wheel Bearing & Hub Assembly (Set of 4) for Models with ABS
  • 2009 Buick Allure Front & Rear Wheel Bearing & Hub Assembly (Set of 4)
  • 2005-2008 Buick LaCrosse Front & Rear Wheel Bearing & Hub Assembly (Set of 4) for Models with ABS
  • 2009 Buick LaCrosse Front & Rear Wheel Bearing & Hub Assembly (Set of 4)
  • 2005 Buick Terraza Front & 4 Bolt Flange Rear Wheel Bearing & Hub Assembly (Set of 4) (excluding All Wheel Drive Models)
  • 2006-2008 Chevy Impala Front & Rear Wheel Bearing & Hub Assembly (Set of 4) for Models with ABS
  • 2009-2013 Chevy Impala Front & Rear Wheel Bearing & Hub Assembly (Set of 4)
  • 2006-2007 Chevy Monte Carlo Front & Rear Wheel Bearing & Hub Assembly (Set of 4) for Models with ABS
  • 2005 Chevy Uplander Front & 4 Bolt Flange Rear Wheel Bearing & Hub Assembly (Set of 4) (excluding All Wheel Drive Models)
  • 2004-2008 Pontiac Grand Prix Front & Rear Wheel Bearing & Hub Assembly (Set of 4) for Models with ABS
  • 2005 Pontiac Montana SV6 Front & 4 Bolt Flange Rear Wheel Bearing & Hub Assembly (Set of 4) (excluding All Wheel Drive Models)
  • 2005 Saturn Relay Front & 4 Bolt Flange Rear Wheel Bearing & Hub Assembly (Set of 4) (excluding All Wheel Drive Models)
$140.45
Save 88%
List: $1,179.78 Save: $1,039.33
Part #: 1ASHS00617

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est