Replaces

1995-2002 Lincoln Continental Wheel Bearing & Hub Assembly Front ( Motorcraft)

This part replaces:

  • Motorcraft HUB12

  • New

Ford/Motorcraft: HUB12

This wheel bearing and hub assembly is a FORD original equipment part! It is the same part that you would receive if you purchased it from your local Ford dealer!

Specifications:

  • Brand NEW Ford/Motorcraft part
  • Fits RH or LH Front
  • Direct replacement
  • Replaces dealer part numbers: 3F132C300BA, 3F13-2C300-BA, 3F1Z1104BA, 3F1Z-1104-BA, F50Y1104A, F50Y-1104-A, F8RZ1104AA, F8RZ-1104-AA, XFI22C300BB, XFI2-2C300-BB, XFIZ1104AEB, XFIZ-1104AE-B, XFIZ1104BA, XFIZ-1104-BA
  • Fits 5 lug wheel
  • Wheel studs already installed

 

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Remove Wheel (1:09 in the video)
    • Remove hub nut
    • Remove lug nuts and remove wheel with an 18mm socket.
  2. Remove tie rod (1:50 in the video)
    • Remove cotter pin.
    • Use your 18 mm socket to remove the nut at the bottom of the tie rod.
    • Use your tie rod puller to pull the tie rod up.
    • Use your two adjustable wrenches to remove the tie rod.
  3. Remove the axle. (2:42 in the video)
    • Disconnect the brake line bracket and ABS sensor
    • Remove the upper stabilizer bolt with an 18mm wrench and a 10 mm wrench to secure it.
    • Remove the lower stabilizer bolt using your 18 mm wrench to secure it and a 21 mm socket.
    • Use a hammer to drive the bolt all the way out.
    • Move the steering knuckle off the strut with a hammer.
    • Tap the axle with a hammer and use a pry bar to pry it out of the steering knuckle.
    • Pry the other end of the axle out.
  4. Remove Brake Caliper (6:00 in the video)
    • Use your 12mm and 15mm socket wrenches to remove the calipers and caliper brackets.
    • Use a wire tie to help prevent stress on the caliper.
    • Use your socket to remove the brackets.
    • Use a wire tie to secure the caliper up out of the way.
  5. Remove the brake rotor (7:00 in the video)
    • Take care not to touch the rotor, and if you do make sure to clean it with rubbing alcohol or mineral spirits.
  6. Remove Hub (7:08 in the video)
    • On this vehicle, the hub is cast iron and the knuckle is aluminum, seizing is a potential issue.
    • Use an air hammer and protective eyewear to break the hub free if this happens.
    • Remove the hub with a hammer.
    • Clean up any corrosion with a wire brush.
  7. Install new hub (9:26 in the video)
    • Use some penetrating oil or anti-seize grease to prep the knuckle for the new hub.
    • Put the three 15 mm bolts in place and tighten the nuts to 70 ft lbs.
    • Check out our other videos to see how to finish putting everything back together.

Tools needed for replacement:

    Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Rust Penetrant
  • Wire Ties

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Sockets - Metric

  • 10mm Socket
  • 11mm Socket
  • 12mm Socket
  • 13mm Socket
  • 14mm Socket
  • 15mm Socket
  • 16mm Socket
  • 17mm Socket
  • 18mm Socket
  • 19mm Socket
  • 20mm Socket
  • 21mm Socket

  • Specialty Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Large Hammer
  • Tie Rod Puller
  • Wire Brush

  • Wrenches - Metric

  • 10mm Wrench
  • 11mm Wrench
  • 12mm Wrench
  • 13mm Wrench
  • 14mm Wrench
  • 15mm Wrench
  • 16mm Wrench
  • 17mm Wrench
  • 18mm Wrench

How-to Video:

(09:55 min)

Tools List:

    Materials, Fluids, and Supplies

  • Anti-Seize Grease
  • Rust Penetrant
  • Wire Ties

  • Ratchets & Related

  • Ratchet
  • Socket Extensions

  • Sockets - Metric

  • 10mm Socket
  • 11mm Socket
  • 12mm Socket
  • 13mm Socket
  • 14mm Socket
  • 15mm Socket
  • 16mm Socket
  • 17mm Socket
  • 18mm Socket
  • 19mm Socket
  • 20mm Socket
  • 21mm Socket

  • Specialty Tools

  • Floor Jack
  • Hammer
  • Jack Stands
  • Large Hammer
  • Tie Rod Puller
  • Wire Brush

  • Wrenches - Metric

  • 10mm Wrench
  • 11mm Wrench
  • 12mm Wrench
  • 13mm Wrench
  • 14mm Wrench
  • 15mm Wrench
  • 16mm Wrench
  • 17mm Wrench
  • 18mm Wrench



This part replaces:

  • Motorcraft HUB12

Vehicle Fit

  • 1996-2006 Ford Taurus Wheel Bearing & Hub Assembly Front ( Motorcraft)
  • 1995-2002 Lincoln Continental Wheel Bearing & Hub Assembly Front ( Motorcraft)
  • 1996-2005 Mercury Sable Wheel Bearing & Hub Assembly Front ( Motorcraft)
$113.95
Part #: MCSHF00008

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates
MOTORCRAFT
Brand #: HUB12

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est