Replaces

2003-2003 Pontiac Grand Prix Wheel Bearing & Hub Assembly Front (excluding ABS Brakes)

Part Details

  • Front / Rear Location: Front

This part replaces:

  • OE # 88964096
  • HOLLANDER 538-01527

  • New

Specifications:

  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • 3 bolt flange
  • Direct replacement
  • Replaces dealer part numbers: 7467558, 12413005, 12413006, 12413139
  • Fits 5 lug wheel
  • Wheel studs already installed
  • Correct for vehicles WITHOUT front wheel ABS

 

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hub & bearings are all tested prior to shipping.

Fit Guaranteed

  • This hub & bearing will install just as your original does. You can use your existing hardware.
  • Save time and money with this direct fit hub bearing assembly. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

2 Year Warranty

This item is backed by a 2 Year Warranty. In the event this item should fail during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Door Panel (0:37)
    • Pry up the door pull trim piece with a flat blade screwdriver
    • Remove the two 7mm bolts from the door pill
    • Pry out the door panel clips with a putty knife
    • Pull the door handle out of the door panel
    • Lift the door panel up and off
    • Push the window switch out of the door panel from behind
    • Disconnect the window switch wiring harness
    • Peel off the water shield, using a razor blade if necessary
  2. Removing the Window Regulator (1:58)
    • Lower the window to access the window clamp nuts
    • Disconnect the window motor wiring harness
    • Loosen the two 10mm nuts from the window clamp
    • Pull the window out of its clamp
    • Unclip the regulator cables from the door
    • Remove the lower two 10mm bolts from the regulator
    • Loosen the top ten mm bolt from the regulator
    • Pull the window regulator out of the door
  3. Installing the New Window Regulator (3:21)
    • Remove the top 10mm bolt from the old regulator
    • Insert the 10mm bolt into the new regulator
    • Hang the new regulator in place by the bolt
    • Insert the lower two 10mm bolts into the regulator
    • Tighten all three 10mm bolts
    • Clip the regulator cables into the door
    • Loosen the 10mm window clamp nuts
    • Connect the window motor wiring harness
    • Lower the window onto its clamps
    • Tighten the 10mm window clamp nuts
    • Put the ignition in accessory mode
    • Connect the window switch wiring harness
    • Test the window with the switch
    • Disconnect the window switch wiring harness
    • Turn the ignition off
  4. Reinstalling the Door Panel (5:02)
    • Put the water shield into place
    • Push the door panel shield onto the door panel
    • Thread the wiring harness through the window switch cavity
    • Lift the door panel into place
    • Push in the door panel clips
    • Connect the window switch wiring harness
    • Push the window switch into the door
    • Insert the two 7mm bolts into the door pull
    • Push in the door pull trim piece

Tools needed for replacement:

    General Tools

  • Putty Knife
  • Razor Blade / Gasket Scraper

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 7mm Socket

How-to Video:

(06:28 min)

Tools List:

    General Tools

  • Putty Knife
  • Razor Blade / Gasket Scraper

  • Ratchets & Related

  • Ratchet

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 10mm Socket
  • 7mm Socket



This part replaces:

  • OE # 88964096
  • HOLLANDER 538-01527

Vehicle Fit

  • 2003-2004 Buick Century Wheel Bearing & Hub Assembly Front (excluding ABS Brakes)
  • 2002-2004 Buick Regal Wheel Bearing & Hub Assembly Front (excluding ABS Brakes)
  • 2003-2005 Buick Rendezvous Wheel Bearing & Hub Assembly Front (excluding ABS Brakes)
  • 2000-2005 Chevy Impala Wheel Bearing & Hub Assembly Front (excluding ABS Brakes)
  • 2000-2005 Chevy Monte Carlo Wheel Bearing & Hub Assembly Front (excluding ABS Brakes)
  • 2003-2005 Chevy Venture Wheel Bearing & Hub Assembly Front (excluding ABS Brakes) (excluding All Wheel Drive Models)
  • 2003-2005 Pontiac Aztek Wheel Bearing & Hub Assembly Front (excluding ABS Brakes)
  • 2003 Pontiac Grand Prix Wheel Bearing & Hub Assembly Front (excluding ABS Brakes)
  • 2003-2004 Pontiac Montana Wheel Bearing & Hub Assembly Front (excluding ABS Brakes) (excluding All Wheel Drive Models)
  • 2005 Pontiac Montana Wheel Bearing & Hub Assembly Front (excluding ABS Brakes)
$60.45
Save 72%
List: $215.98 Save: $155.53
Part #: 1ASHF00069

Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est