Replaces

2006-2008 Lincoln Mark LT 4WD Front Wheel Bearing & Hub Assembly (Timken)

Part Details

  • Front / Rear Location: Front
  • Brands: Timken
  • Transmission/Drivetrain Type: 4WD

This part replaces:

  • HOLLANDER 538-01672
  • Timken SP550207
  • OE # 7L3Z 1104 A

  • New

TIMKEN WHEEL BEARING & HUB ASSEMBLY: SP550207

This replacement hub & bearing assembly is just what you need to get your vehicle in good working order again.

Specifications:

  • Brand New Timken Wheel Bearing & Hub Assembly
  • Fits either LH (Driver Side) or RH (Passenger Side) FRONT
  • 4 Bolt Rectangular Flange
  • Fits 6 Lug Wheel
  • Replaces dealer part number: 7L3Z-1104-A, 7L3Z1104A
  • Has ABS (Anti Lock Brakes) sensor already installed
  • Direct replacement
  • Built to strict quality control standards
  • Fits 4WD (Four Wheel Drive) Models only

Note: For 2005 models you can find the production date of your vehicle on either the outer edge of the driver's front door or on the latch piller that the door closes on.

Note: This part is an authentic Timken brand product that is supplied and packaged by Timken.   In some cases, Timken will source parts from other high quality suppliers such as SKF and Koyo. These parts are subjected to the very same testing and quality standards as all Timken products.

Quality

  • You will not have a problem with our product. If you are comparing us to someone selling a brand name product remember brand names are only as good as the company selling them. Both Bizrate.com and The Better Business Bureau recognize 1A Auto as a trusted online seller. You will be pleased with what you find out about us.
  • You don't want to be delayed by a defective part. 1A Auto wheel hub & bearings are all tested prior to shipping.

Fit Guaranteed

  • This hub & bearing will install just as your original does. You can use your existing hardware.
  • Save time and money with this direct fit hub bearing assembly. No trips to the auto parts store or extra time trying to match up and press bearings.
  • Hub installation is a degree more difficult than changing a tire on most vehicles.

Value

  • Some shops and dealers charge more for parts and repairs when they think the customer doesn't know what is involved. Now you can get the value you deserve. Knowing what this repair entails can be the difference between the value of doing it yourself, or the pain of a costly part or repair bill.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Wheel (0:42)
    • Pry off the center cap with a flat blade screwdriver
    • Loosen the 21mm lug nuts with the vehicle on the ground
    • Remove the hub cap with pliers
    • Loosen the 13mm nut
    • Raise the vehicle with a floor jack
    • Secure the vehicle on jack stands
    • Remove the lug nuts
    • Pull off the wheel
  2. Removing the Brake Pads (1:32)
    • Pry the brake pads into the caliper with a flat blade screwdriver to push in the pistons
    • Remove the 13mm bolts from the brake caliper
    • Pull the caliper aside
    • Pry the brake pads off with a flat blade screwdriver
  3. Removing the Brake Rotor (2:32)
    • Remove the 18mm bolts from the brake caliper bracket
    • Pull off the brake caliper bracket
    • Thread a nut onto the rotor
    • Hit the rotor with a hammer
    • Pull the rotor off
  4. Removing the Hub (2:58)
    • Disconnect the ABS harness sensor
    • Remove the ABS from the harness on the bracket
    • Remove the four 18mm bolts from the hub
    • Remove the 13mm hub nut, making sure you can push the nut in and out
    • Twist in an 18mm bolt to the hub
    • Remove the hub
  5. Installing the Hub (4:42)
    • Grease the set of bearings inside the new hub with bearing grease
    • Apply a light coat of bearing grease to the engaging wheel for the 4WD
    • Insert the hub into place
    • Tighten the 18mm bolts to the hub
    • Tighten the 18mm bolts to 95 foot-pounds of torque
    • Replace and tighten the 13mm hub nut
    • Tighten the 13mm bolt to 20 foot-pounds of torque
    • Push the ABS wire into its respective brackets
    • Replace the hub cap
  6. Installing the New Brake Rotor (6:41)
    • Slide the rotor on
    • Thread on one lug nut to hold the rotor in place
    • Adjust the emergency brake, if necessary
    • Put the bracket back into place
    • Start the 18mm bolts by hand
    • Tighten the bolts to 95 foot-pounds of torque
  7. Installing the New Brake Pads (7:24)
    • Put the caliper on
    • Thread the 13mm bolts by hand
    • Tighten bolts to 25 foot-pounds
    • Remove the lug nut from the rotor
  8. Reattaching the Wheel (8:55)
    • Slide the wheel into place
    • Start the lug nuts by hand
    • Tighten the lug nuts preliminarily
    • Lower the vehicle to the ground
    • Tighten the lug nuts to between 110 foot-pounds in a crossing or star pattern
    • Reattach the center cap
    • Connect the ABS sensor
  9. Testing the Brakes (9:42)
    • Pump your brakes repeatedly until they feel firm
    • Test your brakes at 5 miles per hour and then 10 miles per hour
    • Road test the vehicle

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket
  • 21mm Socket

How-to Video:

(10:13 min)

Tools List:

    General Tools

  • Floor Jack
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Needle nose pliers

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Ratchet
  • Torque Wrench

  • Screwdrivers & Related

  • Flat Blade Screwdriver

  • Sockets - Metric

  • 13mm Socket
  • 18mm Socket
  • 21mm Socket



This part replaces:

  • HOLLANDER 538-01672
  • Timken SP550207
  • OE # 7L3Z 1104 A

Vehicle Fit

  • 2005 Ford F150 Truck 4WD Front 6 Lug Wheel Bearing & Hub Assembly (Built After 11/28/04 Production Date) (Timken)
  • 2006-2008 Ford F150 Truck 4WD Front 6 Lug Wheel Bearing & Hub Assembly (Timken)
  • 2006-2008 Lincoln Mark LT 4WD Front Wheel Bearing & Hub Assembly (Timken)
$195.45
Save 35%
List: $299.97 Save: $104.52
Only 4 left in stock
Part #: TKSHF00190

Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates
Timken
Brand #: SP550207

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est