Replaces

2006-2010 Jeep Commander Water Pump for V6 3.7L

This part replaces:

  • HOLLANDER 324-00846, -874, -106

  • New

This Water Pump is a brand new aftermarket replacement part! It is just what you need to get your Porsche running great again!

Specifications:

  • Brand NEW
    • Not remanufactured
  • Direct replacement
  • Built to strict quality control standards
  • No core charge

Your water pump is a major component of your engine cooling system. If the water pump fails, the engine will overheat causing it to shut down. Water pumps have an indicator that tells you when they are going bad. There is a small hole in the water pump right under the shaft in the middle that the pulley bolts to. As the water pump's bearings wear out coolant seeps by them and leaks through this hole. If you notice a few drops of coolant under the front of your engine this is an indicator your pump is failing. If a water pump fails it will cause engine overheating, and possibly further engine damage. If you have noticed little drops of coolant under the front of your vehicle then inspect the bottom of the water pump to see if it is dripping out of the indicator hole. If your water pump is the problem, then this part is for you. Replace your broken or leaking water pump now with this great fitting replacement part.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Removing the Tensioner (0:41 in the video)
    • Insert the 15mm socket and ratchet into the tensioner
    • Turn the tensioner clockwise to loosen the belt
    • Pull the belt off the alternator
    • Release the tensioner
    • Pull the belt off by hand
    • Remove the 13mm bolt from the tensioner
    • Remove the tensioner
  2. Removing the Water Pump (1:41 in the video)
    • Remove the cap from the reservoir bottle
    • Place a drain pan beneath the drain plug
    • Loosen the drain plug with a 16mm wrench
    • Remove the eight 13mm bolts that line the water pump
    • Remove the water pump
  3. Preparing the Water Pump (2:50 in the video)
    • Clean the surface of the engine block where the water pump mounts
    • Vacuum the area
    • Place the gasket on the new water pump
  4. Installing the New Water Pump (3:18 in the video)
    • Lower the water pump into place on the engine block
    • Replace the eight 13mm bolts
    • Torque the bolts to 40 foot-pounds
  5. Reinstalling the Tensioner and Serpentine Belt (3:53 in the video)
    • Line up the indent on the tensioner with the bolt on the block
    • Replace and tighten the 13mm bolt on the tensioner
    • Familiarize yourself with the route of the serpentine belt
    • Insert the belt on the pulleys following the diagram except for the last pulley
    • Pull the tensioner clockwise with the 15mm socket and ratchet
    • Pull the belt over the last pulley
    • Release the tensioner
  6. Replacing the Coolant (6:00 in the video)
    • Tighten the coolant drain plug with a 16mm wrench
    • Refill the coolant reservoir with the correct anti-freeze
    • Replace the cap
    • Run the engine to disperse the coolant
    • Loosen the bleeder valve with an 8mm Allen bit
    • Remove the cap to the coolant bottle
    • Replace the reservoir bottle with any lost coolant
    • Replace the cap
    • Bleed the engine until all the excess air is out

Tools needed for replacement:

    Allen Wrenches

  • 8mm Allen Wrench

  • Materials, Fluids, and Supplies

  • Cloth Rags

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 13mm Socket
  • 15mm Socket

  • Specialty Tools

  • Drain Pan
  • Funnel
  • Vacuum

  • Wrenches - Metric

  • 16mm Wrench

How-to Video:

(07:39 min)

Tools List:

    Allen Wrenches

  • 8mm Allen Wrench

  • Materials, Fluids, and Supplies

  • Cloth Rags

  • Ratchets & Related

  • Ratchet
  • Torque Wrench

  • Sockets - Metric

  • 13mm Socket
  • 15mm Socket

  • Specialty Tools

  • Drain Pan
  • Funnel
  • Vacuum

  • Wrenches - Metric

  • 16mm Wrench



This part replaces:

  • HOLLANDER 324-00846, -874, -106

Vehicle Fit

  • 2007-2009 Chrysler Aspen Water Pump for V8 4.7L
  • 2000-2007 Dodge Dakota Water Pump for V8 4.7L
  • 2004-2010 Dodge Dakota Water Pump for V6 3.7L
  • 2009-2010 Dodge Dakota Water Pump for V8 4.7L
  • 2000-2007 Dodge Durango Water Pump for V8 4.7L
  • 2004-2009 Dodge Durango Water Pump for V6 3.7L
  • 2009 Dodge Durango Water Pump for V8 4.7L
  • 2007-2011 Dodge Nitro Water Pump for V6 3.7L
  • 2002-2005 Dodge Ram 1500 Truck Water Pump for V6 3.7L
  • 2003-2005 Dodge Ram 1500 Truck Water Pump for V8 4.7L
  • 2007-2010 Dodge Ram 1500 Truck Water Pump for V6 3.7L
  • 2007-2010 Dodge Ram 1500 Truck Water Pump for V8 4.7L
  • 2006-2010 Jeep Commander Water Pump for V6 3.7L
  • 2006-2009 Jeep Commander Water Pump for V8 4.7L
  • 1999-2005 Jeep Grand Cherokee Water Pump for V8 4.7L
  • 2005 Jeep Grand Cherokee Water Pump for V6 3.7L
  • 2008-2010 Jeep Grand Cherokee Water Pump for V6 3.7L
  • 2009 Jeep Grand Cherokee Water Pump for V8 4.7L
  • 2002-2012 Jeep Liberty Water Pump for V6 3.7L
  • 2007-2008 Mitsubishi Raider Water Pump for V6 3.7L
  • 2008 Mitsubishi Raider Water Pump for V8 4.7L
  • 2011-2012 Ram 1500 Truck Water Pump for V6 3.7L
  • 2011-2013 Ram 1500 Truck Water Pump for V8 4.7L
  • 2011 Ram Dakota Water Pump for V8 4.7L
  • 2011 Ram Dakota Water Pump for V6 3.7L
$57.95
Part #: 1AEWP00107

- Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est