Replaces

1998-2000 Volvo S70 Front Lower Control Arm for 2 Bolt Style Driver Side

This part replaces:

  • DORMAN 520-793
  • OE # 8628495

  • New

This replacement front lower control arm is just what you need to bring back the safety and integrity of your vehicle's suspension and steering.

Specifications:

  • Fits LH (Driver Side) FRONT LOWER
  • Replaces dealer part number: 8628495
  • Cast Steel like original
  • New, not remanufactured or refurbished
  • Control Arm Bushings & Ball Joint are included
  • Correct for Models that use 2 Bolts (1 Bolt per Bushing)
    • Does NOT fit models with 4 Bolts

Worn control arm bushings can cause excessive front tire wear, popping or creaking in the front end, extra play in the steering system, and pose a serious safety concern. Replace that heavily rusted, rotted, or damaged front lower control arm with the loose bushings with our high quality all in one replacement.

Lifetime Warranty

This item is backed by a Limited Lifetime Warranty. In the event this item should fail due to manufacturing defects during intended use, we will exchange the part free of charge (excludes shipping charges) for the original purchaser. Please keep your invoice for proof of this warranty.

  1. Step 1: Testing the Tie Rod (0:15)
    • Jack up one of your front wheels.
    • Grab it by the sides of the tire and try to move it back and forth. If you feel more play than just the steering rack moving back and forth, then your tie rod probably needs replacing.
  2. Step 2: Removing the Front Wheel (0:56)
    • If you don't have air tools, you'll want to loosen the lug nuts with the wheel on the ground.
    • Lift the vehicle with a jack, support it with a jack stand, and take the wheel off the rest of the way.
  3. Step 3: Measuring the Tie Rod (1:19)
    • Before you disassemble the tie rod, you want to measure the tie rod. From a fixed point on the rack, like the end of the boot, you want to measure to the middle of the tie rod. Measure a few times to be sure-you're going to set the new tie rod up the same length.
  4. Step 4: Removing the Tie Rod (1:58)
    • You'll see a lock nut at the end of the tie rod. Holding on to the tie rod with a wrench, use your adjustable wrench to loosen that nut about a quarter of a turn
    • There is also am 18 mm bolt that nut that holds the stud on. Remove that. (If you don't have an impact wrench, use a breaker bar or a piece of pip for extra leverage.
    • Separate the tie rod from the steering knuckle by using a tie rod fork. Taking a hammer, you'll drive the tie rod fork between the rod and the knuckle.
    • Once the tie rod is separated from the knuckle, turn it clockwise to get it off the steering rack.
  5. Step 5: Replacing the Tie Rod (3:45)
    • The new tie rod should come with the bolt in it. Take the bolt out for now.
    • Thread the tie rod onto the nut, measure from the same fixed point as before and make sure it measures the same. Take a couple of measurement.
    • Also, make sure you do not twist the shaft that comes out of the steering rack. Doing so will change your alignment.
    • NOTE: Regarding alignments, it’s suggested that you have an alignment performed after you do a replacement like this.
  6. Step 6: Securing the New Tie Rod (4:39)
    • Once you have the measurement correct, then you can put the tie rod back into the steering knuckle and start the bolt on there.
    • The lock nut at the end of the tie rod is an 18 mm nut. Holding the stud of the tie rod with an 8 mm wrench, tighten up the nut with your 18 mm wrench.
    • Once the 18 mm wrench is tight, grab another wrench and hook it on there for leverage. Give it another pull just for good measure.
    • Torque it to 65 foot pounds.
    • Put your wrench onto the inner tie rod to get this locking nut back out against the outer tie rod. Tighten.
  7. Step 7: Replacing the Wheel (5:53)
    • Turn the wheels straight, and put your wheel and tire back on.
    • Start the lug nuts by hand at first to primarily tighten them.
    • Lower the car back onto the ground.
    • Set your torque wrench to 90 – 95 foot pounds and tighten your lug nuts in a star pattern.

Tools needed for replacement:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Torque Wrench

  • Sockets - Metric

  • 18mm Socket
  • 19mm Socket

  • Specialty Tools

  • Tie Rod Fork

How-to Video:

(06:35 min)

Tools List:

    General Tools

  • Floor Jack
  • Hammer
  • Jack Stands

  • Pliers, Cutters & misc Wrenches

  • Adjustable Wrench

  • Ratchets & Related

  • A Piece of Pipe (for leverage)
  • Torque Wrench

  • Sockets - Metric

  • 18mm Socket
  • 19mm Socket

  • Specialty Tools

  • Tie Rod Fork



This part replaces:

  • DORMAN 520-793
  • OE # 8628495

Vehicle Fit

  • 1993-1997 Volvo 850 Front Lower Control Arm for 2 Bolt Style Driver Side
  • 1998-2000 Volvo S70 Front Lower Control Arm for 2 Bolt Style Driver Side
  • 1998-2000 Volvo V70 Front Lower Control Arm for 2 Bolt Style Driver Side
$44.95
Save 74%
List: $169.66 Save: $124.71
Part #: 1ASLF00179

Ships Same Day for orders placed by 5 P.M. ET

Free GROUND SHIPPING

Check Shipping Rates

We're here to help

1A Auto Parts

Customer Feedback

Customer Feedback
"Thanks for the fast reliable service. Great price, and the headlights were as good as oem or better!!! Keep up the good work..."
- Dwuan M.
Read More
Free Shipping!
OR
CALL
TOLL
FREE

888-844-3393

hablamos Español:866-401-3393
SHIPS SAME DAY
For Orders Placed By 5pm Est